PE10X-XXX-XXX-XXXX
PE15X-XXX-XXX-XXXX
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
PE20X-XXX-XXX-XXXX
PE30X-XXX-XXX-XXXX
RELEASED:
(REV. B)
3-26-13
ELECTRONIC INTERfACE
for Diaphragm Pumps
READ THIS MANUAL CAREfULLY BEfORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
PUMP DATA
PE10X-XXX-XXX-XXXX is PE series 1” EXP Diaphragm Pumps with
MODEL DESCRIPTION CHART
PEXX X -X X X X
-XXX-XXX
electronic interface
PE15X-XXX-XXX-XXXX is PE series 1- 1/2” EXP Diaphragm Pumps
with electronic interface
PE20X-XXX-XXX-XXXX is PE series 2” EXP Diaphragm Pumps with
Pump Size
10 - 1” EXP Diaphragm Pumps
15 - 1- 1/2” EXP Diaphragm Pumps
20 - 2” EXP Diaphragm Pumps
30 - 3” EXP Diaphragm Pumps
electronic interface
PE30X-XXX-XXX-XXXX is PE series 3” EXP Diaphragm Pumps with
electronic interface
Center Section
A - Aluminium
S - Stainless Steel
R - Polypropylene
GENERAL DESCRIPTION
Revision Level
This manual is supplemental information for the electronic
interface options on the PE series of pumps. For complete
pump installation, disassembly and reassembly, safety infor-
mation, and other general pump information, please refer to
the PD pump manual that was also included with the pump.
This electronic interface includes options for solenoid control,
end of stroke feedback, leak detection (diaphragm failure),
cycle counting on the major valve, and a ported motor with
no major valve for user-supplied control directly to the two
diaphragm air chambers.
Specialty Code 1 (Blank if no Speciality Code
)
A - Solenoid 120VAC
B - Solenoid 12VDC
C - Solenoid 240VAC
D - Solenoid 24VDC
G - Solenoid 12VDC ATEX
H -
Solenoid 24VDC ATEX
K - Solenoid 220VAC ATEX
N - Solenoid with no coil
P - Ported Motor (no major valve provided)
S - Cycle Sensing on Major Valve
0 -
Standard Valve Block ( No Solenoid)
Solenoid control allows the cycle rate of the pump to be con-
trolled electronically.
Specialty Code 2 (Blank if no Speciality Code
)
E - End of stroke feedback + Leak Detection
F - End of stroke feedback
L - Leak Detection
With Solenoid control, when the solenoid is energized, the
pump strokes and dispenses the fluid in one chamber. When
the solenoid is de-energized, the pump strokes in the oppo-
site direction, dispensing the fluid in the other chamber.
By providing continuous ON - OFF signals to the solenoid, the
fluid transfer rate may be increased or decreased remotely.
End of stroke feedback can be used in conjunction with the
solenoid valve to cycle the pump based upon completion of
each stroke.
0 - No Option
Special Testing
Testing for special testing options, please contact your
nearest ARO Customer Service Representative or Distributor.
The leak detection option incorporates an optical fluid sensor
in each air chamber to provide a signal when a diaphragm
has failed and fluid is leaking through the pump.
The cycle counter option provides a closed contact output
each time the pump completes a cycle. This option is not
available combined with solenoid control.
The ported motor with no major valve is provided as an op-
tion for users who want to supply compressed air directly to
each diaphragm and control the operation of the pump with
their own external air controls
.
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX (800) 892-6276
© 2013
CCN 46750816
PARTS LIST / PEXXS-XXX-XXX-XXXX
Part no
Item Description
Spool
Qty
Part no
Item Description
Qty
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
410
411
413
414
(for Cycle Sensing)
(PEXXS-XXX-XXX-XSXX)
Sensor
95276
111
95835
(1)
PE10S-XXX-XXX-X0XX, PE15S-XXX-
(
XXX-X0XX)
(for Cycle Sensing)
(PEXXS-XXX-XXX-XSXX)
Adapter
PE10S-XXX-XXX-XSXX, PE15S-XXX-
XXX-XSXX)
96583
(
95835-1
95835-2
95651
(1)
(1)
(1)
(1)
(1)
(2)
(4)
Adapter Plate
119380
All PE10S, PE15S with Solenoid
(AII PEXXS with SoIenoid)
PXXXS-XXX-XXX-
Coil ,120 VAC (
PE20S-XXX-XXX-X0XX, PE30S-XXX-
XXX-X0XX)
116218-33
116218-38
116218-35
116218-39
117345-38
117345-39
117345-35
(
)
XAXX
Coil ,12 VDC
PE20S-XXX-XXX-XSXX, PE30S-XXX-
XXX-XSXX)
(
)
PXXXS-XXX-XXX-XBXX
95651-1
95651-2
96323
(
Coil ,240 VAC
All PE20S, PE30S with Solenoid
)
PXXXS-XXX-XXX-XCXX
(
Coil ,24 VDC
121
134
Sleeve
)
)
PXXXS-XXX-XXX-XDXX
(
(PEXXS-XXX-XXX-XPXX)
Coil, 12 VDC ATEX
(M6 x 1 - 6g x 20 mm)
Screw
PXXXS-XXX-XXX-XGXX
96340
(
(PEXXS-XXX-XXX-XPXX)
Coil, 24 VDC ATEX
135 Valve Block
)
PXXXS-XXX-XXX-XHXX
(
95939-3
(1)
PE10S-XXX-XXX-XSXX, PE10S-XXX-
XXX-X0XX)
(
Coil, 220 VAC ATEX
)
PXXXS-XXX-XXX-XKXX
(
PE15S-XXX-XXX-XSXX, PE15S-XXX-
XXX-X0XX)
(
95939-1
95939-6
95939-5
(1)
(1)
(1)
(AII PEXXS with Solenoid)
415 O-Ring
416 O-Ring
417 Screw
114103
114104
96728647
15309974
96957
(1)
(1)
(2)
(1)
(1)
(1)
(1)
All PE10S with Solenoid
(AII PEXXS with Solenoid)
(AII PEXXS with Solenoid)
All PE15S with Solenoid
PE20S-XXX-XXX-XSXX, PE20S-XXX-
XXX-X0XX, PE30S-XXX-XXX-XSXX,
PE30S-XXX-XXX-X0XX)
(
(AII PEXXS with Solenoid)
(AII PEXXS with Solenoid)
(AII PEXXS with Solenoid)
418 Tube
419 Seal
96337-1
(1)
All PE20S, PE30S with Solenoid
96337-3
114102
(1)
(1)
420 Snap Ring
Y147-43
96954
403
(AII PEXXS with SoIenoid)
Valve
(AII PEXXS with Solenoid)
421 Retainer
(for Cycle Sensing)
(PEXXX-XXX-XXX-XSXX)
Magnet
425
407 Adapter
95275
(1)
(1)
(1)
(PEXXS-XXX-XXX-XAXX, PEXXS-XXX-
XXX-XBXX, PEXXS-XXX-XXX-XCXX,
PEXXS-XXX-XXX-XDXX, PEXXS-XXX-
XXX-XGXX, PEXXS-XXX-XXX-XHXX,
PEXXS-XXX-XXX-XKXX, PEXXS-XXX-
XXX-XNXX)
(AII PEXXS with Solenoid)
428 O-Ring
Y325-13
116464
96953
(1)
Solenoid Muffler
429
(AII PEXXS with Solenoid)
PEXXP-XXX-XXX-XXXX (en)
Page 3 of 16
PARTS LIST / PEXXR-XXX-XXX-XXXX
Part no
95276
Part no
Item Description
Qty
(1)
Item Description
Spool
Qty
410
411
413
414
(for Cycle Sensing)
(PEXXR-XXX-XXX-XSXX)
Sensor
111
96293
(1)
PE10R-XXX-XXX-X0XX, PE15R-XXX-
(
XXX-X0XX)
(for Cycle Sensing)
(PEXXR-XXX-XXX-XSXX)
Adapter
96581
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
PE10R-XXX-XXX-XSXX, PE15R-XXX-
XXX-XSXX)
(
96293-1
96293-2
95651
(1)
(1)
(1)
(1)
(1)
(2)
(4)
Coil Nut
119380
(AII PEXXR with SoIenoid)
All PE10R, PE15R with Solenoid
PXXXR-XXX-XXX-
Coil ,120 VAC (
116218-33
116218-38
116218-35
116218-39
117345-38
117345-39
117345-35
PE20R-XXX-XXX-X0XX, PE30R-XXX-
XXX-X0XX)
)
XAXX
(
Coil ,12 VDC
PE20R-XXX-XXX-XSXX, PE30R-XXX-
XXX-XSXX)
)
PXXXR-XXX-XXX-XBXX
(
(
95651-1
95651-2
96323
Coil ,240 VAC
)
PXXXR-XXX-XXX-XCXX
(
All PE20R, PE30R with Solenoid
Coil ,24 VDC
)
)
PXXXR-XXX-XXX-XDXX
(
Sleeve
121
134
(PEXXR-XXX-XXX-XPXX)
Coil, 12 VDC ATEX
PXXXR-XXX-XXX-XGXX
(
(M6 x 1 - 6g x 20 mm)
Screw
96340
(PEXXR-XXX-XXX-XPXX)
Coil, 24 VDC ATEX
)
PXXXR-XXX-XXX-XHXX
(
135 Valve Block
96174-1
(1)
PE10R-XXX-XXX-XSXX, PE10R-XXX-
XXX-X0XX)
(
Coil, 220 VAC ATEX
)
PXXXR-XXX-XXX-XKXX
(
PE15R-XXX-XXX-XSXX, PE15R-XXX-
XXX-X0XX)
(
95834-1
96174-4
95834-4
(1)
(1)
(1)
(AII PEXXR with Solenoid)
415 O-Ring
416 O-Ring
417 Screw
114103
114104
(1)
(1)
(AII PEXXR with Solenoid)
(AII PEXXR with Solenoid)
All PE10R with Solenoid
96728647
15309974
96957
(2)
(1)
(1)
(1)
All PE15R with Solenoid
(AII PEXXR with Solenoid)
418 Tube
419 Seal
PE20R-XXX-XXX-XSXX, PE20R-XXX-
XXX-X0XX, PE30R-XXX-XXX-XSXX,
PE30R-XXX-XXX-X0XX)
(
95789-1
(1)
(AII PEXXR with Solenoid)
(AII PEXXR with Solenoid)
420 Snap Ring
Y147-43
All PE20R, PE30R with Solenoid
95789-3
11481-7
114102
(1)
(1)
(1)
303
Plastic Plug
(
(AII PEXXR with Solenoid)
421 Retainer
96954
(1)
(1)
(1)
(1)
PEXXR-XXX-XXX-XPXX)
(for Cycle Sensing)
(PEXXX-XXX-XXX-XSXX)
Magnet
425
95275
(AII PEXXR with SoIenoid)
403 Valve
407 Adapter
(AII PEXXR with Solenoid)
428 O-Ring
Y325-13
116464
(PEXXR-XXX-XXX-XAXX, PEXXR-XXX-
Solenoid Muffler
XXX-XBXX, PEXXR-XXX-XXX-XCXX,
PEXXR-XXX-XXX-XDXX, PEXXR-XXX-
XXX-XGXX, PEXXR-XXX-XXX-XHXX,
PEXXR-XXX-XXX-XKXX, PEXXR-XXX-
XXX-XNXX)
429
(AII PEXXR with Solenoid)
96953
(1)
PEXXP-XXX-XXX-XXXX (en)
Page 4 of 16
PARTS LIST / PEXXX-XXX-XXX-XXXX
Part no
Y17-51-6
93832-3
59632-1
Item Description
Pipe Plug
Qty
Part no
96969
Item Description
Qty
422 Manifold
(PEXXA-XXX-XXX-XXfX, PEXXA-XXX-
74
(2)
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XX0X),(PEXXS-XXX-XXX-XXfX,
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
PEXXS-XXX-XXX-XX0X)
(1)
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
(2)
(1)
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
Plug
423 Nut
(PEXXA-XXX-XXX-XXLX, PEXXA-XXX-
XXX-XX0X),(PEXXS-XXX-XXX-XXLX,
PEXXS-XXX-XXX-XX0X)
126
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
(1)
96724182
96712666
96964
283 Diaphragm failure Detector
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXLX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXLX)
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
96270-1
(2)
-
424 Lock Washer
(0.417 ft)
404 Tubing
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
(1)
(1)
94981-XXX-X
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
426 Mounting Strap
405 Elbow
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
59756-103
59764-4
(1)
(1)
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
427 Pressure Sensor
408 Male Connector fitting
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
(1)
96961
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
412 Wiring
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,
PEXXS-XXX-XXX-XXfX)
96965
(1)
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-
XXX-XX0X)
Page 5 of 16
PEXXP-XXX-XXX-XXXX (en)
SOLENOID
GENERAL DESCRIPTION
Without end of stroke feedback, solenoid control can only
be used to cycle the pump based on timing. The following
curves represent the flow rates of a pump based on timed
operation of the solenoid at a common operating point of 70
psi air pressure and 30 psi of back pressure.
figure 3
figure 1
figure 2
PEXXP-XXX-XXX-XXXX (en)
Page 6 of 16
SOLENOID PART LIST / PEXXX-XXX-XXX-XXXX
429
413
414
417
403
415
418
416
407
428
105
233
107
200
141
140
135
133
134
�139
421
420
419�
111
138�
137�
136
107
236
figure 4
LUBRICATION / SEALANTS
Apply Lubriplate fML-2 grease (94276) to all “O” rings,
“U” cups and mating parts.
Page 7 of 16
PEXXP-XXX-XXX-XXXX (en)
END Of STROKE
SETTING / OPERATION
GENERAL DESCRIPTION
With end of stroke feedback from a pressure switch, the
solenoid can be used to cycle the pump based on known feed-
back that the pump has fully completed each stroke.
+
pnp
9.6 to
32 V
1
500mA
2
1
DC
pnp
500mA
4
3
-
PRESSURE SWITCH OPERATION
Set
2
3
5
A calibration procedure is necessary for proper operation of
the pressure switch and accurate end of stroke feedback from
the pump. The Reset ring will always have a lower pressure
value than the Set ring.
Reset
6
4
1. Determine the operating air pressure of the pump.
2. The Reset ring should be set to approximately 25% of the
operating pressure of the pump with a minimum of 10 PSI.
3. The Set ring should be set to approximately 50% of the
operating pressure of the pump. This value is more vari-
able depending on the specific operating conditions. The
switch may function properly at much lower values for
the Set ring if the pump is running slowly, or at lower op-
erating pressures. In general, high operating speeds and
pressures require a higher setting value of the Set ring.
4. Operate the pump slowly to ensure proper operation of
the pressure switch. When the pump has shifted to one
side, the yellow LED will illuminate and remain on until
the pump shifts back to the opposite side.
7
figure 5
1. Locking Ring
2. Setting Rings (manually adjustable after unlocking)
3. LED green: supply voltage O.K.
4. Process connection ¼”NPT; tightening torque 25 Nm
5. Setting Marks
6. LED yellow: Set values reached, OUT1 = ON / OUT2 = OFF
7. Internal Thread M5
Minimum distance between Set and Reset = 2% of the
final value of the measuring range.
To obtain the setting accuracy: Set both rings to the mini-
mum value, then set the requested value.
5. If the operating pressure of the pump changes, the
Set ring may need to be adjusted accordingly.
PART LIST / PEXXX-XXX-XXX-XXEX, PEXXX-XXX-XXX-XXfX
423
424
426
422
427
412
405
404
408
figure 6
PEXXP-XXX-XXX-XXXX (en)
Page 8 of 16
LEAK DETECTION (DIAPHRAGM fAILURE DETECTOR)
The diaphragm failure detector components must be
GENERAL DESCRIPTION
installed by a qualified electrician in compliance with all
national, state and local codes and regulations to reduce
the risk of electrical shock or other serious injury during
installation and operation.
An ARO® diaphragm pump equipped with the ARO
Diaphragm Failure Detector warns of a diaphragm failure by
sensing the presence of liquid in the air chamber of the pump.
This system uses a liquid sensor in each of the two air cham-
bers which will send an output signal when fluid is detected.
ARO is not responsible for accidents resulting from im-
proper installation of components or hardware.
HAZARDOUS VOLTAGE. Do not attempt any service
without disconnecting all electrical supply sources.
INSTALLATION AND WARNINGS
NOTE: ALL WIRING MUST COMPLYWITH ALL LOCAL
AND / OR NATIONAL ELECTRICAL CODES.
Electrical codes that apply must be strictly adhered to;
failure to do so may lead to shock hazard or serious injury.
Some local electrical codes may require the installation of
rigid conduit.
PART LIST / PEXXX-XXX-XXX-XXEX, PEXXX-XXX-XXX-XXLX
283
figure 7
LEAK DETECTION (DIAPHRAGM fAILURE DETECTOR) - PINOUT DESCRIPTIONS
96270-1 SENSOR PINOUTS
B
C
A
Pinout
Function
+24 VDC
Ground
Signal
A
B
C
TURCK (PICOFAST) Connector PSW 3M -*/S90
figure 8
Page 9 of 16
PEXXP-XXX-XXX-XXXX (en)
CYCLE COUNTER
This signal may be used to record cycles for maintenance pur-
poses or batching if the discharge volume of each complete
cycle is known.
GENERAL DESCRIPTION
The ARO diaphragm pump cycle counter provides a closed
contact output each time the pump completes a cycle.
PART LIST - PEXXA-XXX-XXX-XSXX / PEXXS-XXX-XXX-XSXX
126
166k
233
140
141k
135
133
134
k 138
200k
132k 176k 101 181 103
111
k 139
k 137
128
136
105
411
410
LUBRICATION / SEALANTS
Apply Lubriplate fML-2 grease (94276) to all “O” rings,
“U” cups and mating parts.
figure 9
PEXXP-XXX-XXX-XXXX (en)
Page 10 of 16
PART LIST - PEXXR-XXX-XXX-XSXX
126
166k
233
140
141k
107
105
133
134
135
200k
132k 176k 101 181 103
k 138
111
k 139
k 137
136
107
236
411
410
LUBRICATION / SEALANTS
Apply Lubriplate fML-2 grease (94276) to all “O” rings,
“U” cups and mating parts.
figure 10
Page 11 of 16
PEXXP-XXX-XXX-XXXX (en)
As a SOURCING switch (see figure 1) for use with PLC’s.
As a SINKING switch (see figure 2) for use with PLC’s.
As a closed contact switch (see figure 3) for use with meters.
OPERATION
Maximum Operating Voltage . . . . . . . . . 200 V DC
Switching Current . . . . . . . . . . . . . . . . . . . . 0.5 Amps
The pump may be interfaced with a control device in the
following ways:
Sourcing Switch
+V
INPUT
Figure 1
Figure 2
Figure 3
Sinking Switch
INPUT
Closed Contact Switch
INPUTS
figure 11
Page 12 of 16
PEXXP-XXX-XXX-XXXX (en)
PORTED NO MOTOR OPTIONS
PART LIST- PEXXA-XXX-XXX-XPXX / PEXXS-XXX-XXX-XPXX
166 k
121
173 k
173 k
121
160
133
134
43
132 k
176 k
101 181 103
figure 12
PART LIST- PEXXR-XXX-XXX-XPXX
166 k 121
173 k
173 k
121
133
160
134
132 k
176 k
101 181 103
figure 13
LUBRICATION / SEALANTS
Apply Lubriplate fML-2 grease (94276) to all “O” rings,
“U” cups and mating parts.
PEXXP-XXX-XXX-XXXX (en)
Page 13 of 16
Page 14 of 16
PEXXP-XXX-XXX-XXXX (en)
PEXXP-XXX-XXX-XXXX (en)
Page 15 of 16
PN 97999-1652
Page 16 of 16
PEXXP-XXX-XXX-XXXX (en)
|