EEC PERSONAL PROTECTIVE EQUIPMENT DIRECTIVE
89/686/EEC Article 10
DECLARATION OF CONFORMITY
We hereby certify that the KENNEDY Welding Helmet Model HAS413
complies with all the relevant provisions of the EC Directive 89/686/EEC
as last amended by EEC Directive 96/58/EEC
Harmonised Standards Applied: DIN 15. EN175S, EN379 4/9-13 ER 1/2/1 DIN CE, ANSI Z87.1
MIG/TIG WELDING HELMET
MODEL HAS413
KEN-885-5020K
Manufactured for KENNEDY TOOLS Wigston Works, Leicester, England.
ISO 9001 REGISTERED COMPANY
Signed:
Position: Director, The Kennedy Group Ltd.
Name: Martin Cooke
Date: 1st August 2004
ꢀ Solar power
ꢀ Auto light sensors
ꢀ Light to Dark:
0.0001 seconds
QUALITY GUARANTEE & WARRANTY
KENNEDY TOOLS carry a one year manufacturers warranty.
ꢀ Dark to Light:
0.1 - 0.5 seconds
KENNEDY TOOLS are designed & manufactured
to the highest standards & specifications.
Assuring the quality and performance required by all sectors of industry.
ꢀ Control switching from
shade to shade 9-13
KENNEDY TOOLS are fully guaranteed against
faulty materials & workmanship.
Should they be found to be defective, they will either be repaired or replaced
free of charge (fair wear and tear and/or misuse excepted).
ꢀ High Impact resistance
ꢀ Clear view filter
Please retain supplier invoice as proof of purchase.
ꢀ Permanent UV/IR
protection up to
DIN 15
AVAILABLE FROM YOUR DISTRIBUTOR
ꢀ Light weight-less
than 0.5kg
KENNEDY TOOLS
Wigston Works, Leicester, England.
INSTRUCTION MANUAL
Download from Www.Somanuals.com. All Manuals SeaPrchleAnadsDeownrleoatda. in this information for future reference.
Kennedy is a registered trade mark of The Kennedy Group Ltd.
© The Kennedy Group Ltd. 09/07
INTRODUCTION
The Kennedy Jet Black Auto welding mask is designed using the latest technology to
automatically protect the user’s eyes from arc light damage and leave both hands free to
increase accuracy, efficiency and therefore productivity.
Fitted with automatic filters that are transparent before welding, it enables the operator to
observe the workpiece clearly. When striking the arc, the filter darkens automatically with
immediate effect. When the arc goes out, the filter will become transparent again. The
switching time from light to dark is approximately 1 millisecond, and the switching time from
dark to light maybe set at between 0.1 - 0.5 second.
The mask is equipped with a continuous darkness-adjusting unit, so the operator may select
an arbitrary darker shade number ranging from 9 to 13.
The mask also provides complete protection against UV/IR to DIN15 even in transparent
mode.
The mask is powered by solar power cells and is equipped with two sets of photo sensors to
sense arc light.
The outer protection plate is made of high polymer materials that are spatter resistant and
thermostable, ensuring a long service life.
TECHNICAL SPECIFICATIONS
Filter dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 x 90 x 8mm
View area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 x 42mm
Light shade number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dark shade number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 13
UV/IR protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIN15
Time from light to dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0001s
Time from dark to light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.1 - 0.5s
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solar cells
Operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . .-5°C - 55°C (23°F - 131°F)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .495g
CONTENTS
Mask including automatic filter lens and controller
Headband
Instruction Manual
6
3
8
OPERATING INSTRUCTIONS
ASSEMBLY
Assemble the mask as shown in fig.1 opposite
7
POWER SUPPLY
Power supply is provided by solar cells controlled with micro circuitry which automatically
turns the helmet on and off without having to touch a switch or button.
fig.1
DARKNESS SELECTION
When you strike an arc, the observation window darkens immediately and at this moment
the operator needs to adjust the darkness shade by turning the knob to the optimum shade
for the current work being undertaken. (see page 6.)
9
10
12
Fitting
All heads are different shapes and sizes, therefore it is important to adjust the headband to
fit and set at the correct observation angle. To do this, firstly adjust the skull strap (8) to
the correct position to locate the sweat band (7) comfortably on your forehead. Secondly,
adjust the tightness by depressing and turning the tightness adjuster (10) to suit - do not
over tighten as this will cause headaches. Finally, loosen the locking nuts (13) to enable
you to pivot the mask to the desired viewing angle on the positioning plate (9) then tighten
the locking nuts again.
6
13
4
1
2 3
5
13
11
MAINTENANCE
5
CHANGING THE PROTECTION PLATES
This welding helmet must always be installed with an inner and outer protection plate
before welding. These may need replacing at some point.
To replace the lens/protection plates:
1. Frame
2. Inner protection plate
3. Automatic filter lens
4. Darkness shade control knob
5. Fixing screw
8. Skull strap
9. Positioning plate
10. Tightness adjuster
11. Positioning point for the positioning plate
12. Fixing screws for headband
13. Locking nut
Firstly, remove the fixing screws (5) and the frame (1).
To remove the inner protection plate (2), lever out with a finger nail from the recess in the
centre above the plate and to replace, locate one side behind the corner tabs then flex in
the middle in order to locate behind the tabs on the other side.
6. Outer Protection plate
7. Sweat band
To remove the outer protection plate (6), first you must remove the filter lens assembly (3)
as above, then from the inside press the outer protection plate in the middle to remove. To
replace, insert the new one, locate one side behind the side tabs on the outside then flex in
the middle in order to locate behind the tabs on the other side.
CLEANING
This welding helmet should be cleaned regularly with a fine soft brush to remove dust and
particles. If absolutely necessary, you may clean with soapy water after removing the filter
lens assembly completely.
To do this, pull the shade adjusting knob off it’s spline, remove the 10mm locking nut then
remove the lens from between protection plates as described above. Do not immerse in
water.
SPARES AVAILABLE
Description
Product
Number
HAI8857983K
HAI8857983E
HAI8850004A
Order Code
Inner Protective Plate
Outer Protective Plate
Head Gear Pad
CTL-885-7983K
CTL-885-7983E
PRO-885-0004A
4
5
|