EasyStart
AX3G
AX3B
AX3A
¾ A great collection of
accurately-crafted Guitar
Amp/Cabinet modeling and
Effects using Korg’s award-
winning “REMS” modeling
technology.
¾ For the Electric Bass:
Superbly crafted Amp,
Cabinet and Effects using
Korg’s REMS modeling
technology.
¾ Multi-effect processor for
Electric Acoustic Guitar
providing essential high
quality effects.
¾ Korg’s “REMS” modeling
technology accurately
reproduces the rich, subtle
sound of other acoustic
guitars; Nylon, Reso, M
Small, G Large, T Large &
more.
¾ 16 of the most coveted
Drive/Amp models, mix and
match with 10 killer
cabinets.
¾ 16 of the most coveted
Drive/Amp models; mix
and match with 10 killer
cabinets.
¾ 30 effects including 10 Pre-
FX: Comp, Wah, Fretless
and Synth. 10 Modulation,
Filter and Pitch effects. 10
Delay/Reverb effects plus a
professional noise reduction
effect.
¾ 30 effects divided into 3 FX
blocks w/ an adjustable
professional noise reduction
effect. 10 Pre FX: Comp,
Wah, Acoustic, Drone, P/U
and more. 10 Modulation,
Filter and Pitch effects. 10
Delay/Reverb effects.
¾ Choose from 9 acoustic
body models or a Mic effect
that emulates the timbre of
your guitar being run
through a condenser
microphone.
¾ 80 Programs: 40 presets
and 40 user
¾ 33 effects including 10 Pre
FX such as Compressor,
Limiter, Exciter and Drone.
A Tone network with Mid
Frequency adjustment, a
Notch Filter, 10 Modulation,
Filter and Pitch effects. 10
Delay/Reverb types and a
Noise Reduction effect.
¾ 80 Programs: 40 presets
and 40 user
¾ A total of 6 simultaneous
FX (3 effects blocks, Noise
Reduction, Drive/Amp and
Cabinet modeling).
¾ A total of 6 simultaneous
FX (3 effects blocks, Noise
Reduction, Drive/Amp and
Cabinet modeling).
¾ Intuitive interface for quick
and easy operation.
¾ Intuitive interface for quick
¾ 43 total effect types, 7 FX
and easy operation.
¾ Function and Value knobs
allow easy access to effect
parameters and other
features.
can be used simultaneously
¾ Delay and Reverb Effects
carry over when changing
between programs with the
same settings.
¾ 80 Programs: 40 presets
and 40 user
¾ Program select foot
switches with large LED
indicators for visibility.
¾ Auto-chromatic tuner
w/mute function
¾ Program select foot
switches with large LED
indicators for excellent
visibility.
¾ Intuitive interface for quick
¾ External expression pedal
and easy operation
jack; volume/wah
¾ Battery or AC-powered
¾ External expression pedal
¾ Battery or AC-powered
jack; volume/wah
¾ External expression pedal
¾ Auto-chromatic tuner
jack; volume/wah
¾ Built in auto-chromatic
w/mute function
tuner w/mute function
¾ Auto-chromatic tuner
¾ Output jack also powers
w/mute function
¾ Battery or AC-powered
headphones
AX3-Series EasyStart
Note:
Tip:
A list of effect parameters can be found in the aforementioned effect chart in the rear of the
manual. This will be very helpful in determining which parameter is being adjusted.
The Original Value Indicator (small dot in the lower right corner of the Program/Value Display)
can be used to indicate the saved effect/ parameter settings of the currently selected program.
Simply put, when the Original Value Indicator is lit, the previously saved effect/parameter setting
has been selected.
Example (all AX3 models)
1.
2.
Select MOD with the Function Knob.
Use the Write (“UP”) & Cancel (“DOWN”) Buttons to select “F2” (CL Flange). Then use the Value Knob to adjust the CL Flange
effect’s Main parameter (SPEED).
3.
Turn the Function Knob clockwise one position to PARAM. Use the Write (“UP”) & Cancel (“DOWN”) Buttons to select “P2”
(DEPTH). Use the Value Knob to adjust the level of the DEPTH parameter.
Note:
In this mode, if you press the Program Up (Value) switch, the current parameter value will be
displayed. If you press the Program Down (Type/Param) switch, it will display to the currently
selected FX type/parameter.
Saving a Program
You’ve tweaked and turned some knobs, and you like the changes that you’ve made – now to save your program:
1.
Set the Function Knob to the “WRITE” position, and press WRITE (“UP”) Button. A User program number will blink in the
Program/Value Display.
2.
3.
Use the Program Up and Down Switches or Value Knob to select the destination program number (1 - 40)
Press the WRITE (“UP”) Button once again, and your program will be stored in the specified location (“CP” will display briefly indicating
the process is complete).
Amp/Line Setting (AX3G only)
The AX3G’s output may be optimized to suit specific monitoring sources via the Amp/Line setting. Amp/Line settings can be
made under the P5 parameter of the Drive/Amp (Note; the amp line setting is only applicable to Amp models {i.e. A0, A1,
A2, A3, etc.} and will not be found on Drive models {i.e. D0, D1, D2, D3, etc.}). Select “A1” if you connect the AX3’s output
to the input of a clean-sounding open back combo. Select “A2” if you connect the AX3’s output to the input of an open back
combo with stronger mid-range content. Select “A3” if you connect the AX3’s output into a sealed back cabinet such as an
amp stack. Select “Ln” if you connect the AX3’s output into a line input such as a mixer, recorder, headphones or any other
full range monitoring source.
3
|