ACCUSPLIT® EAGLE
AE140XL
PEDOMETER
ACCUSPLIT, Inc.
3090 Independence Drive, Suite 148
Livermore, CA 94551 USA
800-935-1996 • 925-290-1900 • FAX 925-290-1930
Eat Right! Walk More! Live Well!
e ACCUSPLIT Lifestyle
970-086
Nov 07
Operating Instructions
Functions
Key Features
•
•
Step counter.
•
Built around the Japanese-made JW200 PedometerEngine™
Step Sensor, the current gold standard for accuracy.
Distance in mi or km.
•
•
Extra Large Digits.
For complete Function Specifications, go to page 24.
The ACCUSPLIT exclusive case makes this the slimmest
available pedometer built around the JW200 Step Sensor.
•
•
Chromed, Spring Steel clip resists breakage.
Case includes two leash slots, for attaching safety leash
on either side. Made from tough polycarbonate plastic.
•
Step filter, can be set from 0-5 steps to further increase
accuracy.
2
3
HOWTO OPENYOUR PEDOMETER
See diagrams at right.
USE IT NOW!
Your pedometer is preset with standardized settings
that allow you to use it now!You can customize the
settings later. Skip to pages 13-16 to use it now!
The cover must be closed for the
pedometer to work.
SETTING UPYOUR PEDOMETER
It’s a good idea to set up your pedometer before first using it.
To record your distance accurately, you will need to set your
stride length.
See page 9 when you are ready to set up your unit.
4
5
Getting Acquainted
Mode
indicator
• Press the MODE button to cycle through the display
modes (Steps and distance.)
See page 16 and Specifications for details.
DIGI-WALKERXL.COM
DIST
Steps
Counted
STEP
SET
• The RESET button sets your counts back to zero.
See page 17 for details.
MODES
• STEP: STEP mode shows step count.
• DIST: DISTANCE mode shows distance traveled (mi/km).
MODE Button
140
XL
JW200
S3-
S1,S2,S4
S3+
RESET Button (yellow)
6
7
RESETTINGYOUR PEDOMETER
VIEWINGYOUR RESULTS
Most people prefer to reset counts daily.To reset your counts:
From STEP or DISTANCE mode, press and hold the yellow
RESET button for at least 2 seconds.You’ll see the values all
go back to zero.
Once you put on your pedometer with the cover closed, it
will automatically begin to record your steps, activity time,
and distance. Repeatedly press the MODE button to cycle
through the pedometer modes:
STEPS g DISTANCE g STEPS
Distance is counted automatically whenever steps are being
counted.
•
DISTANCE is simply stride length x steps.
Note: For extra accuracy, the default Step Filter Setting is 1.
See page 19 to learn more.
16
17
OTHER SETTINGS
The Step Filter and Unit of Measurement settings are
accessed through a special “deep set” mode.
CHANGING STEP FILTER SETTING
While the JW200 PedometerEngine™ Step Sensor is
extremely accurate, some people like to have the ability to
filter out false steps. Therefore, the unit has a variable setting
step filter, to allow fine-tuning to your specific preferences.
You can set the value to any value from 0 – 5 steps. For
example, if the filter is set to “3”, the unit will wait to start
counting steps until more than three steps have been taken in
less than five seconds.
To enter this mode, press and hold the S1 button for 4
seconds.The screen will display a single digit. From within
Deep Set mode, press the S2 button to cycle back and forth
between the Step Filter set point and Choice of Unit System.
Press S3+ (MODE) or S3– (RESET) to change the Step Filter
Setting.
18
19
DIGI-WALKERXL.COM
CHANGING UNITS (English vs. Metric)
Can be set
from 0-5
steps
STEP
DIST
SET
The Pedometer can display either in English units (in, mi, and lb
- this is the default), or in Metric units (cm, km, and kg). From within
Deep Set mode (see pg. 18), press the S2 button to cycle back and
forth between setting the Step Filter set point and Choice of Unit
System.The unit will show either “US” or “EU” (for European Union)
depending on the unit system chosen. If you change units after using
the pedometer, the unit will convert all of your data into the new unit
system when you exit Deep Set model.You can check to see which
system of units you are using by seeing which measurement units
are displayed on the Stride and Weight setting screens.
“US” (English)
or “EU” (Metric)
DIGI-WALKERXL.COM
140
XL
STEP
DIST
SET
JW200
S3-
S1,S2,S4
S3+
Set Step Filter set point
Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode.
Press and hold S4 for 2 seconds to exit Deep Set Mode.
140
XL
JW200
Note:The unit will save any changes and exit set mode after 30
S3-
S1,S2,S4
S3+
seconds unattended.
Set measurement mode
20
21
To replace the battery:
REPLACINGTHE BATTERY AND MASTER RESET
When the display starts to dim or goes blank, it is time to
replace the battery.
1. Insert a coin into the slot on the
bottom of the case, and twist to
loosen the faceplate. Remove
faceplate and set aside.
If the display is not uniformly dim or blank, and appears to
display “erroneous data”, do a Master Reset by pressing all
3 buttons simultaneously for 3 seconds and then release.
The display should go blank, then turn all segments on, then
display 0 steps in Step Mode.
2. Locate the battery holder as seen
Battery
on sketch. Pull out the old battery,
and push a new LR-44 battery into the holder,
with positive terminal (+) facing up.
Note: All the settings will return to their default setting values.
If you need to change the battery, the settings will also revert
to default settings.
3. Snap faceplate back into place, hooking the bottom
two tabs first, then closing by pressing together at the
top two tabs.
22
23
SPECIFICATIONS, FEATURES, and FUNCTIONS
Description of Functions
Email (preferred)
User
REGISTER NOW Please return
your AE140XL Registration to
the Repair Center address in the
warranty, and we will let you know
about future products.
•
•
Counts Steps up to 99,999 then rollover.
Counts distance traveled during step activity, up to
999.99 mi or km, then rollover. Automatically counts
whenever step activity is occurring.
•
Adjustable stride length for greater distance accuracy
(default setting is 21 in/53 cm, but can be set from 12-72 in
(30-180 cm), in 0.25 in / 1 cm increments.
Adjustable Step Filter (default setting is 1 step, but can
be set from 0-5 steps) to increase step count accuracy.
Switchable between English and Metric units, without
losing data (default setting is English units).
NO-PROOF-OF-PURCHASE LIMITEDWARRANTY
Free service for first year of ownership;
$12 fee for service thereafter. See label inside unit for date.
•
•
24
25
INDEX
Battery, replacing . . . . 22-23
Current day’s results,
viewing . . . . . . . . . . . . . .16
Setting Mode, exiting . . . .12
Open your pedometer . . . .4
Safety Leash . . . . . . . . 14-15
Setting up pedometer. . 8-12
Step Filter Setting,
change . . . . . . . . . . . 18-19
Stride Length,
setting. . . . . . . . . . . . . 8-12
Unit of measure,
changing. . . . . . . . . . 18-21
Wearing pedometer . . . . .13
Warranty . . . . . . . . . . . . . .25
26
27
|