ACCUSPLIT
AH120M9 PEDOMETER
ACCUSPLIT, Inc.
2290A Ringwood Ave., San Jose, CA 95131
800-965-2008 • 925-226-0888 • FAX 925-463-0147
Eat Right! Walk More! Live Well!
The ACCUSPLIT Lifestyle
Operating Instructions
990-003B
How to Open your pedometer.
See diagrams at right.
DISPLAYS
CURRENT DAY
Display
8922
16:30
7644
days
1
MEMORY
Display
MEMORY
2
3
5
7
display area (flashes when in memory mode)
The pedometer has two display modes: CURRENT DAY and
MEMORY.
SETTING UP YOUR PEDOMETER
ACCUSPLIT products use a common setting procedure,
S1-S2-S3-S4.
Press S1 for 2 seconds: Enter the SET mode
Press S2: Change the field to be set
Press S3: Change the field value
1. CURRENT DAY display: Memory display area in
lower right of screen is blank and clock is present
in lower left corner.
2. MEMORY display: Memory display area in lower
right of screen shows which day’s results you are
viewing.To enter MEMORY display, press the gray
“M” button.
Return to CURRENT DAY display by repeatedly pressing
the gray “M” button until the memory display area is
blank, and clock returns.
Press S4 for 2 seconds: Exit the SET mode
Make sure you are in CURRENT DAY display when setting up
your pedometer and checking today’s steps.
4
2. Press the gray S3 button to increase the HOUR display.
Hold the button down to change hours quickly.
PM hours are displayed in military time (1:00 PM is
13:00, 2:00 PM is 14:00, etc.).
3. Press the yellow S2 button to switch from the HOUR
display to the MINUTE display.The MINUTE display
will start to blink.
4. Press the gray S3 button to increase the MINUTE
display. Hold the button down to change minutes
quickly.
5. Press and hold the yellow S4 button for 2 seconds to
exit SET mode and return to STEP mode.The display
will stop flashing.
SETTING THE CLOCK
8922
16:30
The clock must be set in order for the memory’s automatic
rollover function to work correctly.
1. Press and hold the gray S1 button for 2 seconds.The
HOUR display will start to blink, showing that you’ve
entered SET mode.
6
CLEARING THE MEMORIES
REPLACING THE BATTERY
Auto Reset: At 3:50 AM every day, the previous day’s STEP
record is automatically saved and STEP display resets to 0.
You do not need to press the RESET button every day.
Manual Reset: To reset today’s STEP data to 0, press and
hold the yellow RESET button for 2 seconds. Note: Resetting
today’s steps before automatic nightly rollover prevents them
from being tallied in memory.
System Reset:To reset all memories to 0 (including the clock),
press the recessed SYSTEM RESET button in the lower left
corner of the front of the display. (Use a pen or the end of
a paper clip.) Note: In case of irregular display due to static
electricity, pressing the SYSTEM RESET button, and then
resetting the CLOCK, will return the unit to normal.
1. When the figures on the display start to blink, it is
time to replace the battery.
2. The unit uses oneType CR2032 3-volt lithium battery.
3. Insert a coin into the slot at the bottom of the body
case.Twist the coin to remove the front case.
4. Locate the BATTERY HOLDING PLATE at the bottom
left corner of the inside case. Remove the plate by
loosening the two small screws with a small Phillips
head screwdriver.
5. Take out the old battery and replace it with a new
battery. Place the battery’s positive (+) terminal
FACE UP while you install it into the pedometer.
16
17
CAUTION: Please DO NOT TOUCH inner pedometer parts,
other than battery. Touching the sensor mechanism may
affect the accuracy of the pedometer.
and back case together, then pressing the bottom of
the case together. If the two halves don’t go together
easily, check if the front case is upside down!
6. Reinstall the BATTERY HOLDING PLATE
by tightening the two
screws. Put the case
back together by
7. Reset the CLOCK to restore all functions to your
pedometer.
matching the
top edges of
the front case
NO-PROOF-OF-PURCHASE LIMITEDWARRANTY
Free service for first year of ownership;
$12 fee for service thereafter. See label inside unit for date.
Terminal
Screws
18
19
|