Washer-Extractors
Cabinet Freestanding
CFD6C
Para bajar una copia de estas instrucciones
(If this machine changes ownership, this manual must accompany machine.)
Part No. 9001001R4
April 2007
.........................................................................................
3
Table of
Contents
..............................................................................
7
....................................................................
9
Control Identification............................................................................ 10
............................................................................................. 11
Load the Machine ................................................................................. 11
Start a Program ..................................................................................... 12
Advance Mode...................................................................................... 13
Stop the Machine .................................................................................. 14
Error Messages ..................................................................................... 15
........................................................................................ 19
Daily ..................................................................................................... 19
Yearly ................................................................................................... 21
© Copyright 2007, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
9001001
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Notes
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
2
Introduction
Model Identification
Information in this manual is applicable to these
models:
HX18PVQM6 SX18PVQM6
HX18PVQM7 SX18PVQM7
HX18PVXM6 SX18PVXM6
HX18PVXM7 SX18PVXM7
UX18PVNA6
UX18PVNA7
UX18PVPA6
UX18PVPA7
UX18PVQA6
UX18PVQA7
UX18PVQM6
UX18PVQM7
UX18PVXA6
UX18PVXA7
UX18PVXM6
UX18PVXM7
UX25PVNA6
UX25PVNA7
UX25PVPA6
UX25PVPA7
UX25PVQA6
UX25PVQA7
UX25PVQM6
UX25PVQM7
UX25PVXA6
UX25PVXA7
UX25PVXM6
UX25PVXM7
UX35PVNA6
UX35PVNA7
UX35PVPA6
UX35PVPA7
UX35PVQA6
UX35PVQA7
UX35PVQM6
UX35PVQM7
UX35PVXA6
UX35PVXA7
UX35PVXM6
UX35PVXM7
HX18PVQU6
HX18PVXU6
SX18PVQU6
SX18PVXU6
UX18PVNU6
UX18PVPU6
UX18PVQU6
UX18PVXU6
18
HX25PVQM6 SX25PVQM6
HX25PVQM7 SX25PVQM7
HX25PVXM6 SX25PVXM6
HX25PVXM7 SX25PVXM7
HX25PVQU6
HX25PVXU6
SX25PVQU6
SX25PVXU6
UX25PVNU6
UX25PVPU6
UX25PVQU6
UX25PVXU6
25
HX35PVQM6 SX35PVQM6
HX35PVQM7 SX35PVQM7
HX35PVXM6 SX35PVXM6
HX35PVXM7 SX35PVXM7
HX35PVQU6
HX35PVXU6
SX35PVQU6
SX35PVXU6
UX35PVNU6
UX35PVPU6
UX35PVQU6
UX35PVXU6
35
continued
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
3
Introduction
continued
HX55PVNU6
HX55PVNU7
HX55PVQU6
HX55PVQU7
HX55PVXU6
HX55PVXU7
SX55PVNU6
SX55PVNU7
SX55PVPU6
SX55PVPU7
SX55PVQU6
SX55PVQU7
SX55PVXU6
SX55PVXU7
SX75PVNU6
SX75PVNU7
SX75PVQU6
SX75PVQU7
UX55PVNU6
UX55PVNU7
UX55PVPU6
UX55PVPU7
UX55PVQU6
UX55PVQU7
UX55PVXU6
UX55PVXU7
UX75PVNU6
UX75PVNU7
UX75PVPU6
UX75PVPU7
UX75PVQU6
UX75PVQU7
55
HX75PVNU6
HX75PVNU7
HX75PVQU6
HX75PVQU7
75
HX100PVNU6 SX100PVNU6 UX100PVNU6
HX100PVNU7 SX100PVNU7 UX100PVNU7
HX100PVQU6 SX100PVQU6 UX100PVPU6
HX100PVQU7 SX100PVQU7 UX100PVPU7
UX100PVQU6
100
135
165
UX100PVQU7
HX135PVNU6 SX135PVNU6 UX135PVNU6
HX135PVNU7 SX135PVNU7 UX135PVNU7
HX135PVQU6 SX135PVQU6 UX135PVPU6
HX135PVQU7 SX135PVQU7 UX135PVPU7
UX135PVQU6
UX135PVQU7
HX165PVNU6 SX165PVNU6 UX165PVNU6
HX165PVNU7 SX165PVNU7 UX165PVNU7
HX165PVQU6 SX165PVQU6 UX165PVPU6
HX165PVQU7 SX165PVQU7 UX165PVPU7
UX165PVQU6
UX165PVQU7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
4
Introduction
Nameplate Location
Replacement Parts
The nameplate is located at the rear of the machine.
Always provide the machine’s serial number and
model number when ordering parts or when seeking
technical assistance.
If literature or replacement parts are required, contact
the source from which the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.
1
Customer Service
For technical assistance, call (920) 748-3121.
CFD6C
1
Nameplate
Figure 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
5
Introduction
Model Number Familiarization Guide
Sample Model Number: *X55PVXM60001
Model Number Prefix
Washer-Extractor Capacity (pounds dry weight of laundry)
*X
55
P
Type of Electrical Control (P = WE-6 Computer)
Washer-Extractor Speed Capabilities
Electrical Characteristics
V
X
Design Series
M6
0001
Option Identification (varies from machine to machine)
* Denotes Brand
X55PVXM60001
*
12
15
50 60
2/3+PE
1/3
1000
55
25
EXAMPLE OF NAMEPLATE
CFD29N
Figure 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
6
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Throughout this manual and on machine decals, you
will find precautionary statements (“DANGER,”
“WARNING,” and “CAUTION”) followed by specific
instructions. These precautions are intended for the
personal safety of the operator, user, servicer, and
those maintaining the machine.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
DANGER
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, or other
WARNING
flammable or explosive substances as they give
off vapors that could ignite or explode.
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas is
flammable, do not smoke or use an open flame
during this time.
CAUTION
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
6. Do not allow children to play on or in the washer.
This appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
7
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
19. Replace worn power cords and/or loose plugs.
20. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
21. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT
bypass the loading door switch by permitting the
washer to operate with the loading door open.
22. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power source.
13. Use washer only for its intended purpose,
washing textiles.
23. Always follow the fabric care instructions
supplied by the textile manufacturer.
14. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
24. Never operate the washer with any guards and/or
panels removed.
15. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
25. DO NOT operate the washer with missing or
broken parts.
26. DO NOT bypass any safety devices.
27. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
16. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
instructions may result in conditions which can
produce bodily injury and/or property damage.
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
17. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
18. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a qualified
service person.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
8
Preliminary Information
About the Control
Power Failure Recovery
WE-8 computer on the washer-extractor is an
advanced, programmable computer that allows the
owner to create wash programs.
If a cycle is in process and the power fails, cycle status
is saved in memory without power being applied.
If power resumes, the control will enter into the Start
Mode at the beginning of the cycle step where the
power failed.
The control is factory set-up with 42 pre-programmed
cycles and is ready for operation. Refer to Pre-
Programmed Cycles section in the Programming
manual.
WE-8 allows the owner to program custom cycles on
the machine or with a PC and the Alliance planner
software.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
9
Operation
For 100 - 165 models:
Load the Machine
Push on the doorlock system to open the door.
For 18 - 75 models:
Push the black button and pull the door handle towards
you to open the door.
M179A
CFD63N
Figure 4
Figure 6
Load the drum to the specified capacity.
Load the drum to the specified capacity.
Close the door by pushing the door handle towards the
machine.
Close the door by pushing the door handle towards the
machine.
M179B
Figure 5
CFD64N
Figure 7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
11
Operation
Start a Program
Cycle 00
After powering up the control, “Cycle 00” will show
on the display.
Press the desired program number
(example: program 23).
Cycle 23
The display will show the cycle (example: “Cycle
23”).
Press “Start” to run the program.
No Cycle 23
If the program does not exist, the display will show
“No Cycle 23”. See program mode to create a
program.
Please close
door
If the door is not closed, the display will show “Please
close door”. After closing the door the program will
start.
If the door is closed and the program exists, the
program will start. The name of the program will show
on the display for 2 seconds and the machine will start.
Restaurant 2
S01 C23 0:04:59
80°F High
When the machine is started the display will show the
following information.
S01: Step 1
C23: Program number 23
0:04:59: The time of step 1. This will count down to
0 and then go to step 2 (S02).
80°F:
The temperature of the bath that is
programmed.
High:
The water level in step 1 that is
programmed.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
12
Operation
Special Options in Run Mode
S01 C23 0:04:59
80°F High
While the machine is running press the “Display
Temp” button.
Level : 2.5 cm
62°F 40rpm L
Level:
2.5 cm: Water level in the bath. If the
machine is filling with water this value will
increase. If in a drain step this value will
decrease.
62°F:
The water temperature.
40rpm: The measured rpm of the drum.
L:
Rotation direction of the drum
L (left), R (right)
Press the “Display Temp” button to go back.
S01 C23 0:04:59
80°F High
Advance Mode
Press the “Advance” button to proceed to the next step
in the progam.
Chemical Hold Feature
Chemical supply injection can be paused. Refer to
section Setup of the Chemical Hold Feature in
Programming manual.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
13
Operation
Stop the Machine
S01 C23 0:04:00
Spin 1
Press the Stop button.
Waterlevel
10.2 cm
If there is water in the machine the display will show
“Waterlevel xx.x cm” while the machine is draining
the water.
Coast down
If the machine is spinning the display will show
“Coast down”.
Please open door
When the water is out and the drum has stopped
moving the display will flash between “Please open
door” and “Done cycle 23” until the door is open.
Done Cycle 23
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
14
Operation
Error Messages
Door error
If the door is closed after start the control will try to
lock the door. If the door will not lock “Door error”
will display.
Possible Faults:
●
●
●
Wiring is not connected properly.
Coil to lock the door has failed.
Mechanical problem on the door lock.
Didn’t fill
within time
If machine does not reach programmed water level
within time programmed for step, a fill alarm occurs.
Machine will continue filling and agitating, while
sounding beeper and flashing “Didn’t fill within time”
on display.
Enter to retry
Clear to stop
Condition will continue for up to two (2) minutes. If
programmed water level is reached before two minute
fill alarm time ends, condition ends, and machine
resumes operation. If Enter key is pressed during fill
alarm, condition will end and step will start over. If
programmed water level is not reached within
programmed step time, fill alarm will occur again. If
Clear (STOP) key is pressed while fill alarm is in
effect, cycle will end, and door will unlock. If no
action is taken, and fill level is not reached within
two minute alarm time limit, cycle will end and door
can be unlocked (provided no water level is sensed).
Whenever a fill alarm occurred during a cycle, display
will repeat following messages at end of stop routine,
before door is opened, to indicate alarm condition
occurred in cycle.
Done
Cycle CC
Please open door
Didn’t fill
within time
During step N
(CC = cycle number;
N = step number in which the
alarm occurred).
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
15
Operation
Possible Faults:
●
Wiring is not connected properly to the inlet
valves.
●
●
●
●
The inlet valve is broken.
There is a problem with the water supply.
The inlet valves are blocked by dirt.
The water pressure hose is broken or not
connected properly.
Didn’t drain
within time
If drain step is NOT followed by a spin and if machine
does not empty within the time programmed for drain
step, a drain alarm occurs. Display will read “Didn’t
drain within time.”
Enter to retry
Clear to stop
Done
Cycle CC
During drain alarm, beeper sounds on and off, and
machine continues attempting to drain. If machine
does not empty, condition continues. If Enter key is
pressed, drain alarm ends, and drain step starts over at
beginning. If machine has not emptied when drain step
time expires, alarm occurs again. If Clear (STOP) key
is pressed while drain alarm is in effect, display shows
water level (inches or centimeters), but otherwise takes
no new action since machine has not emptied.
Please open door
Didn’t drain
within time
When cycle ends, display repeats following messages
briefly until door is opened (to indicate that an alarm
condition occurred in the cycle):
During step N
If machine drains during a spin step prior to
accelerating into high speed and if machine has not
emptied within approximately 2 minutes of starting
drain procedure, a drain alarm occurs. There is no
rotation during this alarm; messages displayed are
identical to drain alarm during a drain step not
followed by a spin. Pressing Enter (START) during
drain alarm in a spin step ends alarm and begins spin
step again at start, with machine rotating at wash speed
forward, then to distribution speed. After drain begins
(i.e., drain open, pumping begins), if 2 additional
minutes elapse, alarm occurs again.
(CC = cycle number;
N = step number in which the
alarm occurred).
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
16
Operation
If there was a problem during heating in a step at the
end of the program, the control will show
“Temperature sensor error”. The temperature was
never reached in this cycle.
Temperature
sensor error
Possible Faults:
●
Bad temperature probe.
●
Wiring to electrical or steam heating relay has
failed.
●
Electrical heating elements or steam valve is
broken.
Rotation
sensor error
The control did not sense any pulses or the control
sensed wrong pulses from the rpm sensor.
Possible Faults:
●
Rpm sensor is broken.
●
Distance from rpm sensor to pulley is too large
(>2mm).
●
●
●
●
Bad motor.
V-belt is broken.
Problems with the inverter.
Wiring connection is bad.
An error occurred at the end of a spin stop or during
coast down, where the rpm sensor suddenly failed to
give output pulses.
Speed detection
error
Possible Faults:
●
●
●
●
Rpm sensor failure.
Rpm sensor dislocated (too far from pulley).
Broken V-belt.
Wiring disconnected.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
17
Notes
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
18
Maintenance
Routine maintenance maximizes operating efficiency
Daily
and minimizes downtime. The maintenance
procedures described below will prolong the life of the
machine and help prevent accidents.
1. Inspect water inlet valve hose connections on the
back of the machine for leaks.
CAUTION
2. Inspect steam hose connections for leaks, where
applicable.
Replace all panels that are removed to
perform service and maintenance
procedures. Do not operate the machine
with missing guards or with broken or
missing parts. Do not bypass any safety
3. Verify that insulation is intact on all external
wires and that all connections are secure. If bare
wire is evident, call a service technician.
4. Check door interlock before starting operation:
devices.
SW019
a. Attempt to start the washer with the door
open. The washer should not start with the
door open.
Daily, weekly, monthly, and yearly checklists are
provided at the end of this section. Laminate the
checklists to preserve them for repeated copying.
Operators and technicians are encouraged to add
checks specific to their machine’s particular
application. When possible, space is provided on the
checklists for this purpose.
b. Close the door and start the machine. Attempt
to open the door while the cycle is in progress.
The door should not open.
The following maintenance procedures must be
performed regularly at the required intervals.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
19
Maintenance
Weekly
1. Clean the fan of the AC drive box.
1. Check the machine for leaks.
2. Clean the entire cabinet of the machine regularly
and remove all traces of soap, etc.
a. Start an unloaded cycle to fill the machine.
b. Verify that door and door gasket do not leak.
3. Remove all detergent residue in the soap
dispenser with hot water.
c. Verify that the drain valve is operating. If
water does not leak out during the prewash
segment, drain valve is closed and functioning
properly.
4. Clean the door gasket and remove all detergents
and other products.
5. Shut off the main water, steam and power
connections at the end of each day. Do not
change the setting of the water inlet taps on boiler
fed machines once these have been installed.
Monthly
6. It is recommended to leave the door and the soap
dispenser open after use, to ventilate the
machine.
1. Clean the AC drive Box.
a. Remove the AC drive box cover.
b. Blow the fins clean using compressed air at a
pressure of 60-90 psi or by using canned
compressed air. Use care to avoid damaging
cooling fan or other components.
2. V-belts.
a. Check V-belts for uneven wear and frayed
edges.
b. Verify that V-belts are properly aligned by
checking pulley alignment. Place a
straightedge across both pulley faces. The
straightedge should make contact with the
pulleys in four places.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
20
Maintenance
3. Remove back panel and check overflow hose and
drain hose for leaks.
Yearly
1. Replace the automatic lubricator (only for 75-
100-135-165 machine). Failure to do so could
void the warranty.
4. Clean inlet hose filter screen:
a. Turn water off and allow valve to cool, if
necessary.
2. Check if the machine is working properly. If you
see or hear any abnormal function on the
machine call a service technician.
b. Unscrew inlet hose and remove filter screen.
c. Clean with soapy water, rinse and reinstall.
Replace if worn or damaged.
5. Check the supply dispenser hoses for leaks.
6. Use compressed air to clean lint from motor.
7. Clean interior of machine, both basket and shell,
by wiping with a water-soaked sponge or cloth.
8. Use compressed air to ensure that all electrical
components are free of moisture and dust.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
21
Maintenance
Daily Preventive Maintenance
Checklist
Machine ____________________________
Week of: ________________
Days
Operator ___________________________
Checks
1
2
3
4
5
6
7
Beginning of Day
1. Inspect water inlet valve hose connections on the back of the
machine for leaks.
2. Inspect steam hose connections for leaks, where applicable.
3. Verify that insulation is intact on all external wires and that all
connections are secure.
4. Inspect door lock and interlock before starting operation:
a. Attempt to start the machine with door open.
b. Close the door and start the machine. Attempt to open the door
while the cycle is in progress.
5.
End of Day
1. Clean the fan of the AC drive box.
2. Clean the entire cabinet of the machine.
3. Remove all detergent residue in the soap dispenser with hot water.
4. Clean the door gasket and remove all detergents and other products.
5. Shut off the main water, steam and power.
6. Leave loading door open at the end of each day to ventilate the
machine.
7.
NOTE: Unload the machine promptly after each completed cycle to prevent moisture buildup.
NOTE: Leave loading door open after each completed cycle to allow moisture to evaporate.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
22
Maintenance
Weekly Preventive Maintenance
Checklist
Machine ____________________________
Operator ___________________________
Month __________
Week Ending:
Checks
/
/
/
/
/
1. Check the machine for leaks:
a. Start an unloaded cycle to fill the machine.
b. Verify that door and door gasket do not leak.
c. Verify that the drain valve is operating.
2.
3.
4.
5.
6.
7.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
23
Maintenance
Monthly Preventive Maintenance
Checklist
Machine ____________________________
Month
Operator ___________________________
Checks
Observe All Safety Warnings!
Disconnect power to the machine before performing the monthly maintenance procedures.
1. Clean the AC drive box.
2. V-belts
a. Check V-belts for uneven wear and frayed edges.
b. Verify that V-belts are properly aligned by checking pulley alignment.
3. Remove back panel and check overflow hose and drain hose for leaks.
4. Clean inlet hose filter screen.
5. Check the supply dispenser hoses for leaks.
6. Use compressed air to clean lint from motor.
7. Clean interior of machine, both basket and shell, by wiping with a water-soaked
sponge or cloth.
8. Use compressed air to ensure that all electrical components are free of moisture and
dust.
9.
10.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
24
Maintenance
Yearly Preventive Maintenance
Checklist
Machine ____________________________
Year
Operator ___________________________
Checks
Observe All Safety Warnings!
Disconnect power to the machine before performing the quarterly maintenance procedures.
1. Replace the automatic lubricator (only for 75-100-135-165 machines).
2. Check if the machine is working properly. If you see or hear any abnormal function
on the machine call a service technician.
3.
4.
5.
6.
7.
8.
9.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001001
25
|