Dryer
DCY 7202 XW3
User Manual
2960311039_EN/220115.1711
1 Important instructions for safety and
environment
This section contains safety instructions that will help protect from risk of
personal injury or property damage. Failure to follow these instructions shall
void any warranty.
1.1 General safety
•The dryer can be used by children at and above 8 years old and by
persons whose physical, sensory or mental capabilities were not fully
developed or who lack experience and knowledge provided that they
are supervised or trained on the safe usage of the product and the risks
it brings out. Children should not play with the product. Cleaning and
maintenance works should not be performed by children unless they are
supervised by someone.
•Children of less than 3 years should be kept away unless continously
supervised.
•Adjustable feet should not be removed. The gap between the dryer and
the floor should not be reduced with materials such as carpet, wood and
tape. This will cause problems with the dryer.
•Always have the installation and repairing procedures carried out by the
Authorized Service. Manufacturer shall not be held liable for damages
that may arise from procedures carried out by unauthorized persons.
•Never wash the dryer by spraying or pouring water onto it! There is the
risk of electric shock!
Dryer / User Manual
3 / 28 EN
Important instructions for safety and environment
1.1.1 Electrical safety
A Electrical safety instructions should be followed while electrical
connection is made during the installation.
•Connect the dryer to a grounded outlet protected by a fuse at the value
specified on the type label. Have the grounding installation performed by
a qualified electrician. Our company shall not be liable for any damages
that will arise when the dryer is used without grounding in accordance
with the local regulations.
•The voltage and allowed fuse protection is stated on the type label plate.
•The voltage specified on the type label must be equal to your mains
voltage.
•Unplug the dryer when it is not in use.
•Unplug the dryer from the mains during installation, maintenance,
cleaning and repair works.
•Do not touch the plug with wet hands! Never unplug by pulling on the
cable, always pull out by grabbing the plug.
•Do not use extension cords, multi-plugs or adaptors to connect the dryer
to power supply in order to decrease the risk of fire and electric shock.
•Power cable plug must be easily accessible after installation.
B Damaged mains cable should be changed notifying the Authorized
B If the dryer is faulty, it must not be operated unless it is repaired
Service.
by an authorized service agent! There is the risk of electric shock!
Dryer / User Manual
4 / 28 EN
Important instructions for safety and environment
1.1.2 Product safety
Points to be taken into consideration for fire hazard:
Below specified laundry or items must not be dried
in the dryer considering fire hazard.
•Unwashed laundry items
•Items soiled with oil, acetone, alcohol, fuel oil, kerosene, stain
removers, turpentine, paraffin or paraffin removers must be
washed in hot water with plenty of detergent before being dried
in the dryer.
For this reason especially the items containing the above
specified
stains must be washed very well, to do this
use adequate detergent and choose a high washing
temperature.
Below specified laundry or items must not be dried in the
dryer due to the fire hazard:
•Garments or pillows bolstered with rubber foam (latex foam),
shower bonnets, water resistant textiles, materials with rubber
reinforcement and rubber foam pads.
•Clothing cleaned with industrial chemicals.
Items such as lighter, match, coins, metal parts, needle etc.
may damage the drum set or may lead to functional problems.
Therefore check all the laundry that you will load into your dryer.
Never stop your dryer before
the programme completes. If you must do this, remove all
laundry
quickly and lay them out to dissipate the heat.
Clothes that are washed inadequately may ignite on their own
and even may ignite after drying ends.
Dryer / User Manual
5 / 28 EN
Important instructions for safety and environment
•You must provide enough ventilation in order to prevent gases exiting from
devices operating with other types of fuels including the naked flame from
accumulating in the room due to the back fire effect.
Underwear that contains metal reinforcements should not be
A
dried
in the dryer. Dryer may be damaged if metal reinforcements come
loose and break off during drying.
Use softeners and similar products in accordance with the
instructions of their manufacturers.
C
C
Always clean the lint filter before or after each loading. Never
operate the dryer without the lint filter installed.
•Never attempt to repair the dryer by yourself. Do not perform any repair
or replacement procedures on the product even if you know or have the
ability to perform the required procedure unless it is clearly suggested in
the operating instructions or the published service manual. Otherwise, you
will be putting your life and others’ lives in danger.
•There must not be a lockable, sliding or hinged door that may block
the opening of the loading door in the place where your dryer is to be
installed.
•Install your dryer at places suitable for home use. (Bathroom, closed
balcony, garage etc.)
•Make sure that pets do not enter the dryer. Check the inside of the dryer
before operating it.
•Do not lean on the loading door of your dryer when it is open, otherwise it
may fall over.
•The lint must not be allowed to accumulate around the tumble dryer
Dryer / User Manual
6 / 28 EN
Important instructions for safety and environment
1.2 Mounting over a washing machine
•A fixing device should be used between the two machines when installing
the dryer above a washing machine. The fitting device must be installed
by the authorized service agent.
•Total weight of the washing machine and the dryer -with full load- when
they are placed on top of each other reaches to approx. 180 kilograms.
Place the products on a solid floor that has sufficient load carrying
capacity!
Washing machine cannot be placed on the dryer. Pay attention
to the above warnings during the installation on your washing
A machine.
Installation Table for Washing Machine and Dryer
Washing Machine Depth
Dryer Depth
62cm 60 cm 54 cm 50 cm 49 cm 45 cm 40 cm
Can be
Can be
Can be
Can be
Can be
Can be Cannot be
54 cm
60 cm
installed installed installed installed installed installed installed
Can be
Can be
Can be
Can be
Can be Cannot be Cannot be
installed installed installed installed installed installed installed
Dryer / User Manual
7 / 28 EN
Important instructions for safety and environment
1.3 Intended use
•Dryer has been designed for domestic use. It is not suitable for
commercial use and it must not be used out of its intended use.
•Use the dryer only for drying laundry that are marked accordingly.
•The manufacturer waives any responsibility arisen from incorrect usage or
transportation.
•The service life of the dryer that you purchased is 10 years. During this
period, original spare parts will be available to operate the dryer properly.
1.4 Child safety
•Packaging materials are dangerous for the children. Keep packaging
materials away from children.
•Electrical products are dangerous for the children. Keep children away
from the product when it is operating. Do not let them tamper with the
dryer. Use the child-proof lock in order to prevent the children to tamper
with the dryer.
Child-proof lock is on the control panel. (See Child lock)
C
•Keep loading door closed even when the dryer is not in use.
Dryer / User Manual
8 / 28 EN
Important instructions for safety and environment
1.5 Compliance with the WEEE regulation
and disposing of the waste product
This product complies with EU WEEE Directive (2012/19/EU). This
product bears a classification symbol for waste electrical and
electronic equipment (WEEE).
This product has been manufactured with high quality parts and
materials which can be reused and are suitable for recycling. Do
not dispose of the waste product with normal domestic and other
wastes at the end of its service life. Take it to the collection center for the
recycling of electrical and electronic equipment. Please consult your local
authorities to learn about these collection centers.
1.6 Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive
(2011/65/EU). It does not contain harmful and prohibited materials
specified in the Directive.
1.7 Package information
Packaging materials of the product are manufactured from recyclable
materials in accordance with our National Environment Regulations. Do
not dispose of the packaging materials together with the domestic or other
wastes. Take them to the packaging material collection points designated
by the local authorities.
Please visit the following website to get more information on the product.
Dryer / User Manual
9 / 28 EN
Important instructions for safety and environment
1.8 Technical Specifications
EN
Height (Min. / Max.)
Width
Depth
84,6 cm / 86,6 cm*
59,5 cm
54 cm
7 kg**
36 kg
Capacity (max.)
Net weight (plastic front door usage)
Net weight (glass front door usage)
Voltage
38 kg
Rated power input
Model code
See type label***
* Min. height: Height with adjustable feet are closed.
Max. height: Height with adjustable feet are opened maximum.
** Dry laundry weight before washing.
*** Type label is located behind the loading door.
Technical specifications of the dryer are subject to specification
without notice to improve the quality of the product.
Figures in this manual are schematic and may not match the
product exactly.
Values stated on markers on the dryer or in the other published
documentation accompanying with the dryer are obtained in
laboratory in accordance with the relevant standards. Depending
on operational and environmental conditions of the dryer, these
values may vary.
C
C
C
Dryer / User Manual
10 / 28 EN
2 Your Dryer
2.1 Package Contents
1
2
3
4
5
1. Water drain hose *
2. Filter drawer spare sponge*
3. User Manual
4. Drying basket*
5. Drying basket user manual*
*It can be supplied with your machine depending on its model.
Dryer / User Manual
11 / 28 EN
3 Installation
3.2 Removing the transportation
safety assembly
Before the calling the nearest Authorized Service for the
installation of the dryer, ensure that electrical installation
and water drain is appropriate referring to the user's
manual.(See 3.3 Connecting to the drain and 3.5
Electrical connection) If they are not suitable, contact
a qualified electrician and technician to make necessary
arrangements.
Remove the transportation safety
assembly before using the dryer for the
first time.
A
Open the loading door.
There is a nylon bag inside the drum that contains a
piece of styrofoam. Hold it from its section marked with
XX XX.
Preparation of the dryer's location
as well as the electrical and waste
water installations is under customer's
C
Pull the nylon towards yourself and remove the
transportation safety assembly.
responsibility.
Prior to installation, visually check if the
dryer has any defects on it. If the drier
A is damaged, do not have it installed.
Damaged products cause risks for your
safety.
3.1 Appropriate installation location
Install the dryer on a stable and level surface.
Dryer is heavy. Do not move it by yourself.
•
Operate your dryer in a well ventilated, dust-free
environment.
•
The gap between the dryer and the surface should
not be reduced by the materials such as carpet,
wood and tape.
Do not cover the ventilation grills of the dryer.
There must not be a lockable, sliding or hinged
door that may block the opening of the loading
door in the place where your dryer is to be
installed.
Once the dryer is installed, it should stay at the
same place where its connections have been
made. When installing the dryer, make sure that
its rear wall does not touch anywhere (tap, socket,
etc.).
Place the dryer at least 1 cm away from the edges
of other furniture.
Your dryer can be operated at temperatures
between +5°C and +35°C. If the operating
conditions fall outside of this range, operation of
the dryer will be adversely affected and it can get
damaged.
The rear surface of the tumble dryer shall be
placed against a wall.
Check that no part of the transportation
safety assembly remains inside the drum.
A
•
•
3.3 Connecting to the drain
In products equipped with condenser unit, water
accumulates in the water tank during the drying cycle.
You should drain accumulated water after each drying
cycle.
You can directly drain accumulated water through the
water drain hose supplied with the product instead of
periodically draining the water collected in the water
tank.
•
•
•
Connecting the water drain hose
1-2 Pull hose at the behind of the dryer by hand in
order to disconnect it from where it is connected.
Do not use any tools to remove the hose.
3
Connect one end of the drain hose supplied with
the dryer to the connection point from where you
removed the hose of the product in previous step.
•
4
Connect the other end of the drain hose directly to
the wastewater drain or to the washbasin.
Do not place the dryer on the power
cable.
B
Dryer / User Manual
12 / 28 EN
Installation
3.5 Electrical connection
For specific instructions for electrical connection
required during installation (see 1.1.1 Electrical
Safety)
1
2
4
3.6 Transportation of the dryer
Unplug the dryer before transporting it.
Drain all water that has remained in the dryer.
If direct water drain connection is made, then remove
the hose connections.
3
We recommend carrying the dryer in
upright position. If it is not possible to
carry the machine in the upright position,
we recommend carrying it by tilting
A
towards the right side when looked from
the front.
Hose connection should be made in a safe
manner. Your drain house will be flooded if
the hose comes out of its housing during
water discharge.
3.7 Changing the illumination lamp
In case an illumination lamp is used in your laundry
dryer.To change the Bulb/LED used for illumination of
your tumble dryer, call your Authorized Service.
The lamp(s) used in this appliance is not suitable for
household room illumination. The intended purpose of
this lamp is to assist the user to place laundry in the
tumble dryer in a comfortable way.
A
Water drain hose should be attached to a
height of maximum 80 cm.
C
C
Make sure that the water drain hose is not
stepped on and it is not folded between the
drain and the machine.
3.4 Adjusting the feet
In order to ensure that the dryer operates more silently
and vibration-free, it must stand level and balanced on
its feet. Balance the machine by adjusting the feet.
Turn the feet to left or right until the dryer stands level
and firmly.
Never unscrew the adjustable feet from
their housings.
C
Dryer / User Manual
13 / 28 EN
4 Preparation
4.1 Laundry suitable for drying in the dryer
Always obey the instructions given on the garment tags. Dry only the laundry having a label stating that they are
suitable for drying in a dryer and make sure that you select the appropriate programme.
LAUNDRY DRYING SYMBOLS
Drying
Symbols
Suitable for
dryer
No Iron
Do not dry-
clean
Sensitive /
Delicate dry
Do not dry
with dryer
Do not dry
Drying
Settings
Iron -
Iron at high
temperature
Iron at medium
temperature
Iron at low
temperature
Dry or Steam
IRON
200 0C
150 0C
110 0C
Maximum temperature
4.2 Laundry not suitable for drying in 4.4 Things to be done for energy
the dryer
saving
Following information will help you use the dryer in an
ecological and energy-efficient manner.
Delicate embroidered fabrics, woolen, silk
garments, delicate and valuable fabrics,
airtight items and tulle curtains are not
suitable for machine drying.
•
Spin your laundry at the highest speed possible
when washing them. Thus, the drying time is
shortened and energy consumption is reduced.
Sort out the laundry depending on their type and
thickness. Dry the same type of laundry together.
For example thin kitchen towels and table clothes
dries earlier than thick bathroom towels.
Follow the instructions in the user manual for
programme selection.
C
•
4.3 Preparing laundry for drying
•
Laundry may be tangled with each other after
washing. Separate the laundry items before
placing them into the dryer.
•
•
•
•
Dry garments having metal accessories such as
zippers, inside out.
Fasten the zippers, hooks and buckles and button
sheets.
Do not open the loading door of the machine
during drying unless necessary. If you must
certainly open the loading door, do not to keep it
open for a long time.
•
•
Do not add wet laundry while the dryer is in
operation
Clean the lint filter before or after each drying
cycle. (See 6.1 in Maintenance and cleaning)
Dryer / User Manual
14 / 28 EN
Preparation
•
Clean the condenser regularly at least once every
month or after every 30 drying cycles. (See 6.4 in
Maintenance and cleaning)
Ventilate the room, where the dryer is located, well
during drying.
It is not recommended to load the dryer
with laundry exceeding the level indicated
in the figure. Drying performance will
degrade when the machine is overloaded.
Furthermore, dryer and the laundry can get
damaged.
C
•
4.5 Correct load capacity
Following weights are given as examples.
Follow the instructions in the “Programme selection and
consumption table”. Do not load more than the capacity
values stated in the table.
Approximate weights
Laundry
(g)*
1500
1000
500
350
700
250
100
700
350
150
300
200
500
350
700
100
125
Cotton quit covers (double)
Cotton quit covers (single)
Bed sheets (double)
Bed sheets (single)
Large tablecloths
Small tablecloths
Tea napkins
Bath towels
Hand towels
Blouses
Cotton shirts
Shirts
Cotton dresses
Dresses
Jeans
Handkerchiefs (10 pieces)
T-Shirts
*Dry laundry weight before washing.
Dryer / User Manual
15 / 28 EN
5 Operating the product
5.1 Control panel
1
4
3
2
1. On/Off/Program selection button
2. Start/Pause button
3. Delay time button
4. Audio alarm level button
5.2 Screen symbols
Iron dry
Freshen End/anti-
Cupboard Cupboard
Cottons Synthetics
Extra
Xpress
Shirts
Spin
Timer
Up
creasing
dry
dry plus
programs
dry
Child-proof
lock
Buzzer
Mix
On/Off
Start
pause
cancel
Tank
full
Dryness
Level
Filter
cleaning
Daily
Jeans
Timer Volume up
Delay
BabyProtect Sport
Start/
Wait/
Ready
Drying
Mute
Delicates
Dryer / User Manual
16 / 28 EN
Operating the product
•
When you select the desired program by using
On/off/program selection button, the machine will
5.3 Preparation of Tumble Dryer
•
•
•
Plug in the tumble dryer.
turn on.
Open the loading door.
Place the laundry into the tumble dryer without
overloading.
1
•
Push and close the loading door.
Take care not to trap any laundry inside
the loading door.
A
4
3
2
Selection of program by using On/off/
program selection button doesn’t mean
that the program has been started.
Press the Start/Pause button to start the
program.
C
5.4 Program selection
There are 15 programs included in your tumble drier.
1
4
3
2
•
Program selection and consumption table have
been given in the order that might be mostly
preferred by users.
Dryer / User Manual
17 / 28 EN
Operating the product
5.5 Program selection and consumption table
Spin Speed
Capacity in Washing
Programs
Program Description
Drying Time (min)
(kg)
Machine
(rpm)
You may dry all your cotton laundry in this program. (T-shirt, pants,
pyjamas, baby clothes, underwear, linen, etc.) You can put your
laundry in the wardrobe without ironing.
Cotton Cupboard dry
7
1000
1000
116
120
You may use this program for extra dryness in thick laundry such as
pants, tracksuit.
Cotton Cupboard dry +
7
You can put your laundry in the wardrobe without ironing.
You may dry your cotton laundry to be ironed in this program to have
them slightly damp for ease of ironing. (Shirt, T-shirt, tablecloth, etc.)
Cotton Iron Dry
Cotton Extra Dry
7
7
1000
1000
90
You may dry your thick cotton laundry in this program such as towels,
bathrobe, etc. You can put your laundry in the wardrobe without
ironing.
124
You may dry all your synthetic laundry in this program. (Shirt, T-shirt,
underwear, tablecloth, etc.) You can put your laundry in the wardrobe
without ironing.
Synthetic Cupboard dry
Synthetic Iron Dry
3.5
3.5
800
800
45
35
You may dry your synthetic laundry to be ironed in this program to
have them slightly damp for ease of ironing. (Shirt, T-shirt, tablecloth,
etc.)
Jeans
Daily
You may dry denim pants, skirts, shirts or jackets in this program.
4
1200
600
80
59
You may dry both your cotton and synthetic daily laundry in this
program.
1.5
It dries the shirts in a more sensitive manner, and causes less
creasing and easier ironing.
Shirt
1.5
4
1200
1000
40
92
You may dry your sports clothes that are appropriate for tumble drying
in this program.
Sport
You may dry your delicate laundry or laundry with hand wash symbol
(silk blouses, thin underwear, etc.) at low temperature in this program.
Delicates
2
-
600
-
40
10
It just provides airing for 10 minutes without any hot air. You can air
the cotton and linen laundry that are kept closed for a long time , and
eliminate the odour in them.
Freshen up
You may select from time programs between 10 and 20 and 40
minutes to achieve the desired drying level at low temperature. In this
program, tumble drier’s operation lasts for the set time independently
from the dryness of laundry.
Timer programmes
-
-
-
Dryer / User Manual
18 / 28 EN
Operating the product
* : Energy Label standard program (EN 61121:2012) All the filters must be cleaned prior to test series.
All values in the table have been specified as per the EN 61121:2012 standard. Consumption values may vary from
the values in the table depending on the variances in laundry type, spin speed, ambient conditions, and voltage
values.
Energy consumption values
Spin Speed in Washing
Machine (rpm)
Approximate residual Energy consumption
Programs
Capacity(kg)
moisture content
value (kWh)
Cotton Wardrobe Dryness*
Cotton Iron Dryness
7
7
1000
1000
800
60%
60%
40%
4,17
3,25
1,42
Synthetic Wardrobe Dryness
3,5
Power consumption of the off-mode for the standart cotton programme at full load, PO (W)
Power consumption of the left-on mode for the standart cotton programme at full load, PL (W)
0,5
1,0
„Cotton cupboard dry programme“ used at full and partial load is the standard drying programme
to which the information in the label and the fiche relates, that this programme is suitable for drying
normal wet cotton laundry and that it is the most efficient programme in terms of energy consumption
for cotton.
To obtain better results from your dryer, your laundry must be washed at suitable programs and spun at
the recommended speed in the washing machine.
C
C
There may be a little moisture on the shirts at the end of the programme. We recommend you not to
leave the shirts in the dryer.
Dryer / User Manual
19 / 28 EN
Operating the product
5.6 Auxiliary functions
Laundry may be added or removed during
the delay time. At the end of countdown
for Delay Time, Delay Time warning
indicator turns off and drying starts.
Audio alarm
C
An audio alarm is heard when the program is completed
in the tumble drier. If you do not want to hear the audio
alarm, please press the “Audio Alarm” button. When you
press the audio alarm button, the light turns on and you
hear no alarm at the completion of program.
Changing the delay time
If you want to change the time during countdown:
•
Cancel the program by turning On/off/program
selection button. Repeat the Delay time selection
process after selecting the desired program.
You may select this function before or
after the program starts.
C
Cancelling the delay time function
If you want to cancel the delay time countdown and start
the program immediately:
5.7 Warning indicators
•
Cancel the program by turning On/off/program
selection button. Press the “Start/Pause” button
after selecting the desired program.
Warning indicators may vary depending
on the model of your tumble drier.
C
Filter cleaning
The warning indicator turns on to show that the filter
needs to be cleaned.
5.7 Starting the program
Start the program by pressing the Start/Pause button.
Indicators of Start/Pause/Ready and Drying turn on to
show that program has started.
Water tank
The warning indicator turns on to show that the water
tank needs to be drained.
If the water tank fills during the operation of program,
warning indicator flashes and machine pauses. In
such a case, drain the water in water tank and start
the program by pressing Start/Pause button. Warning
indicator turns off and program is resumed.
5.8 Child Lock
There is a child lock in the tumble drier that prevents the
program flow from being affected when the buttons are
pressed during operation of program. When the Child
Lock is active, all buttons on the panel are disabled
except for the On/off/program selection button.
In order to activate the child lock, press and hold the
Delay time and Audio alarm buttons spontaneously for
3 seconds.
Delay time
If you prefer to dry your laundry after a certain period of
time, you may delay the start of program up to 3, 6 or 9
hours thanks to the delay function.
Once the program is completed, the child lock must
be disabled to start a new program or intervene in
the program. Press and hold the same buttons for 3
seconds to disable the child lock.
Open the loading door, and put the laundry in.
Select the drying program.
•
•
By pressing the Delay time selection button, set
the desired delay time. When the Delay time button
is pressed one more time, 3-hour delay is selected
and relevant indicator light turns on. When the
same button is pressed again, 6-hour delay is
selected, and one more pressing causes 9-hour
delay. If the delay time button is pressed once
more, the delay is cancelled.
When the Child Lock is enabled, child
lock warning indicator on the display
turns on.
C
Child lock is disabled when the tumble
drier is turned off and turned on again
C
by using the On/off/program selection
After the selection of Delay time, delayed operation
is started for the selected program by pressing
“Start/Pause” button.
button.
Child lock is disabled when the machine
is turned off and turned on again by using
C
the On/off/program selection button.
When the child lock is active:
If the position of program selection button is changed
while the tumble drier is running or paused, indicator
symbols do not change.
Dryer / User Manual
20 / 28 EN
Operating the product
5.10 Cancelling the program
When the program selection switch is
turned while the tumble drier is running
and child lock is active, two beeps are
heard. If the child lock is cancelled
without restoring the program selection
to switch to its previous position, program
is ended because the position of program
selection switch is changed.
When you want to cancel the program and end the
drying process for any reason after the tumble drier has
started operation, the program is cancelled by turning
the On/off/program selection button.
C
WARNING: When you cancel the
program during the operation of tumble
A drier, inner part will be extremely hot;
therefore, allow it to cool down by running
the airing program.
5.9 Changing the program after
starting
After the tumble drier starts running, you may dry your
laundry in a different program by changing the selected
program.
5.11 End of program
At the end of program, Fibre Filter Cleaning and Water
Tank warning symbols on the program monitoring
indicator turn on. Loading door can be opened, and the
tumble drier will be ready for a second operation.
In order to turn off the tumble drier, put the On/Off/
Program selection button in On/Off position.
•
For instance, in order to select Extra Dry instead
of Iron Dryness program, select the Extra Dry
program by turning the On/off/program selection
button.
Start the p rogram by pressing the Start/Pause button.
Adding or removing laundry during pause
If you want to add or remove laundry after the drying
program has started:
When the laundry isn’t removed after the
end of program, 2-hour anti-creasing
•
Put the tumble drier into Pause position by
pressing the Start/Pause button. Drying process
stops.
Open the loading door in Pause position, and close
the door after adding or removing laundry.
Start the program by pressing the Start/Pause
button.
C
function is enabled in order to prevent
creasing of laundry. Program spins the
laundry at intervals of 10 minutes, and
prevents creasing.
•
•
Clean the fibre filter after each drying.
(See: “Fibre filter and Loading door inner
C
C
surface”)
The process of adding laundry after
the start of drying process might lead
to mixing of wet laundry with the dried
laundry inside the tumble drier and some
damp laundry at the end of process.
Drain the water tank after each drying.
(See: “Draining the water tank”)
C
Laundry adding and removing process
can be repeated as many times as
C
desired during drying. But this process
leads to extension in the program time
and increase in energy consumption
since it will repeatedly interrupt the during
process. Therefore, it is recommended to
add laundry before starting the program.
If a new program is selected by changing
the position of program selection button
while the tumble drier is paused, the
running program ends.
C
Do not contact the inner surface of drum
while adding or removing laundry during a
running program. Surface of drum is hot.
Dryer / User Manual
21 / 28 EN
6 Maintenance and cleaning
Service life of product extends and frequently
experienced problems will be reduced if it is cleaned at
regular intervals.
6.1 Cleaning Lint Filter / Loading Door
Inner Surface
Lint and fiber released from the laundry to the air during
the drying cycle are collected in the Lint Filter.
•
Clean the entire inner surface of the loading door
and loading door gasket with a soft damp cloth.
Such fiber and lint are generally formed
during wearing and washing.
C
A
Always clean the lint filter and the inner
surfaces of the loading door after each
drying process.
You can clean the lint filter housing with a
vacuum cleaner.
C
To clean the lint filter:
•
•
Open the loading door.
Remove the lint filter by pulling it up and open the
lint filter.
•
•
Clean lint, fiber, and cotton raveling by hand or with
a soft piece of cloth.
Close the lint filter and place it back into its
housing.
6.2 Cleaning the sensor
There are dampness sensors in the dryer that detect
whether the laundry is dry or not.
To clean the sensors:
•
•
Open the loading doorof the dryer.
Allow the machine to cool down if it is still hot due
to the drying process.
•
Wipe the metal surfaces of the sensor with a soft
cloth, dampened with vinegar and dry them.
•
A layer can build up on the filter pores that can
cause clogging of the filter after using the dryer
for a while. Wash the lint filter with warm water
to remove the layer that builds up on the lint
filter surface. Dry the lint filter completely before
reinstalling it.
Clean metal surfaces of the sensors 4
times a year.
C
C
Do not use metal tools when cleaning
metal surfaces of the sensors.
Dryer / User Manual
22 / 28 EN
Maintenance and cleaning
•
Drain the water in the tank.
Never use solvents, cleaning agents or
similar substances for cleaning due to the
risk of fire and explosion!
A
•
•
If there is lint accumulation in the funnel of the
water tank, clean it under running water.
Place the water tank into its seat.
If the direct water draining is used as
an option, there is no need to empty the
C
water tank.
6.3 Draining the water tank
Dampness of the laundry is removed and condensed
during drying process and the water that arise
accumulates in the water tank. Drain the water tank
after each drying cycle.
6.4 Cleaning the condenser;
Hot and humid air in the condenser is cooled with the
cold air from the room. Thus, the humid air circulating in
your dryer is condensed and then pumped into the tank.
Clean the condenser after every 30 drying
Condensed water is not drinkable!
cycles or once a month.
C
A
Never remove the water tank when the
program is running!
To clean the condenser:
1. If a drying process has been carried out, open the
door of the machine and wait until it cools down.
A
If you forget to drain the water tank, the machine will
stop during the subsequent drying cycles when the
water tank is full and the Water Tank warning symbol
will flash. If this is the case, drain the water tank and
press Start / Pause button to resume the drying cycle.
To drain the water tank:
Pull the drawer and remove the water tank carefully.
Dryer / User Manual
23 / 28 EN
Maintenance and cleaning
2. Unlock the 2 condenser locks after opening the kick
plate.
6. Close the kick plate cover.
3. Pull out the condenser.
4. Clean the condenser by applying pressurized water
with a shower armature and wait until the water
drains.
5. Place the condenser in its housing. Fasten the 2 locks
and make sure that they are seated securely.
Dryer / User Manual
24 / 28 EN
7 Troubleshooting
Drying process lasts for a long time.
•
•
•
Pores of the fibre filter might be clogged. >>> Wash the filter with warm water.
Condenser might be clogged. >>> Wash the condenser.
Ventilation grills at the front of machine might be blocked. >>> Remove any items in front of the ventilation
grills that block ventilation.
Ventilation might be inadequate if the installation area is very small. >>> Open the windows and doors in
order to prevent excessive increase in room temperature.
•
•
•
•
There might be furring on the damp sensor. >>> Clean the damp sensor.
Laundry might be overloaded. >>> Do not overload the tumble drier.
Laundry might not have been adequately spun. >>> Increase the rpm of tumble drier.
Laundry is still wet at the end of drying.
Hot laundry unloaded at the end of drying feel wetter than they really are.
C
•
You may not have used a program suitable for laundry type.>>> Check the maintenance labels on the
laundry and select a program suitable for their type, or use the time programs additionally.
Pores of the fibre filter might be clogged. >>> Wash the filter with warm water.
Condenser might be clogged. >>> Wash the condenser.
•
•
•
•
Laundry might be overloaded. >>> Do not overload the tumble drier.
Laundry might not have been adequately spun. >>> Increase the rpm of tumble drier.
Tumble drier does not turn on or program cannot be started. Tumble drier does not activate when set.
•
•
•
The power cord might not be plugged in. >>> Make sure the power cord is plugged in.
Loading door might be open. >>> Make sure that the loading door is properly closed.
You may not have set the program or pressed the Start/Pause button. >>> Make sure that you have set the
program and it is not in Pause position.
•
Child lock might be active. >>> Disable the child lock.
Program was interrupted for no reason.
•
•
•
Loading door might not be properly closed. >>> Make sure that the loading door is properly closed.
A power cut might have occurred. >>> Press the Start/ Pause button to start the program.
Water tank might be full. >>> Drain the water tank.
Laundry is shrunk, felt or worn out.
•
You may not have used a program suitable for laundry type. >>> Check the maintenance labels on the
laundry and select a program suitable for their type.
The lighting inside the tumble drier does not turn on. (In models with lamps)
•
You may not have turned on the tumble drier be using On/Off/Cancel button. >>> Make sure that the tumble
drier is at ‘on’ position.
Lamp might be broken. >>> Contact the Authorized Service for the replacement of lamp.
•
Filter cleaning warning led is on.
Fibre filter might not have been cleaned. >>> Clean the filter.
Filter cleaning warning led flashes.
•
•
•
•
Filter bearing might be clogged with fibre. >>> Clean the filter bearing.
There might be a layer in the filter pores that causes clogging. >>> Wash the filter with warm water.
Condenser might be clogged. >>> Wash the condenser.
Dryer / User Manual
25 / 28 EN
Troubleshooting
Water is leaking from the condenser cover.
•
There might be fibre build-up inside the loading door and on the surfaces of loading door gasket. >>> Clean
the inner surfaces of loading door and surfaces of loading door gasket.
Loading door opens itself.
Loading door might not be properly closed. >>> Push the loading door until you hear the closing sound.
Water tank warning led is on/flashes.
•
•
•
Water tank might be full. >>> Drain the water tank.
Water drain hose might be folded. >>> Check the water drain hose if the product is directly connected to the
water outlet.
If you cannot eliminate the problem despite following these instructions, please contact the vendor that
.sold you the product or an Authorized Service. Do not try to repair the product yourself
A
Dryer / User Manual
26 / 28 EN
8 Electrical Connection
Make sure that you have an earthed power outlet
socket rated at 13 amps (minimum).
Important
Fitting a different plug
A
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals on
your plug, proceed as follows:
1 Connect the green - yellow or green (earth) wire
to the terminal in the plug marked ‘E’ or with the
symbol or coloured green and yellow or green.
2 Connect the blue (neutral) wire to the terminal in
the plug marked ‘N’ or coloured black.
Attention!
If you use your dryer as built-in, the socket must
be reachable after installation, or a separate
switch (which can disconnect the two poles) must
be used in the installation. Check for suitability.
For a permanent connection, a master switch with
at least 3mm contact clearance and minumum 13
A rating must be used.
Electrical requirements
3 Connect the brown (live) wire to the terminal in
the plug marked ‘L’ or coloured red.
Before you insert the plug into the wall socket
make sure that the voltage and the frequency
shown in the rating label corresponds to your
electricity supply.
With the alternative plugs a 13A fuse must be
fitted either in the plug or adaptor or in the main
fuse box. If in doubt contact a qualified electrician.
We recommend that this appliance be connected
to the mains supply via a suitable switched and
fused socket in a readily accessible position.
Should the mains lead of the appliance become
damaged or need replacing at any time, it must
be replaced by a special purpose made mains
lead which can only be obtained from a Authorised
Service Agent.
Green and yellow
or green
A Warning
This appliance must be earthed
N
L
Blue or black
Brown or red
If the fitted moulded plug is not suitable for your
socket, then the plug should be cut off and an
appropriate plug fitted.
The moulded plug on this appliance incorporates a
13A fuse. Should the fuse need to be replaced an
ASTA approved BS1362 fuse of the same rating
must be used. Do not forget to refit the fuse cover.
In the event of losing the fuse cover, the plug must
not be used until a replacement fuse cover has
been fitted. Colour of the replacement fuse cover
must be the same colour as that visible on the pin
face of the plug. Fuse covers are available from
any good electrical store.
In order to avoid hazards, damaged supply cord
should be replaced by the manufacturer, its service
agent or similarly qualified people.
Dryer / User Manual
27 / 28 EN
|