JANUARY 2005
AC1020A
AC1021A-XMIT
AC1021A-REC
RGBHV Video with Stereo Audio
Fiber Optic Transmission System
NEED
P/N 123231 Rev.A
© Copyright 2005. Black Box Corporation. All rights reserved.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
CUSTOMER
SUPPORT
INFORMATION
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax: 724-746-0746
Web site: www.blackbox.com
•
E-mail: [email protected]
AC1020A/AC1021A-XMIT/ AC1021A-REC
Trademarks
TRADEMARKS USED IN THIS MANUAL
UL is a registered trademark of Underwriters Laboratories Incorporated.
Any other trademarks used in this manual are acknowledged to be the
property of the trademark owners.
FCC sTaTemeNT
FEDERAL COMMUNICATIONS COMMISSION
AND
CANADIAN DEPARTMENT OF COMMUNICATIONS
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used properly, that is, in strict accordance with the manufacturer’s
instructions, may cause interference to radio communication. It has been tested
and found to comply with the limits for a Class A computing device in accordance
with the specifications in Subpart B of Part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when the equipment is oper-
ated in a commercial environment. Operation of this equipment in a residential area
is likely to cause interference, in which case the user at his own expense will be
required to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for com-
pliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission
from digital apparatus set out in the Radio Interference Regulation of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la classe A prescrites dans le Règle-
ment sur le brouillage radioélectrique publié par le ministère des Communications
du Canada.
1
AC1020A/AC1021A-XMIT/ AC1021A-REC
AC1020A/AC1021A-XMIT/ AC1021A-REC
OPeraTING POINTers & TrOUBLesHOOTING
NOm sTaTemeNT
Normas Oficiales Mexicanas (NOM)
Optical Fiber:
Electrical Safety Statement
The RGBHV with StereoAudio fiber optic transmission system is designed to operate
INSTRUCCIONES DE SEGURIDAD
with most multimode (MM) and single mode (SM) optical fibers.
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de
Remember to check the attenuation and bandwidth of the fiber optic cable. The
system will only operate properly if these specifications fall within the range of the
system’s loss budget.
que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para refer-
encia futura.
Troubleshooting:
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de oper-
Multimode fiber optic cable contains an optical fiber with a light carrying “core” that
is only .0025 inches (62.5 microns) in diameter. Single mode fiber optic cable has an
even smaller “core”, only 00032 to .0004 inches (8-10 microns). This is smaller than
a human hair! Therefore, any minute particles of dirt or dust can easily block the fiber
from accepting or radiating light. To prevent this from happening, always use the
provided dust caps whenever optical connectors are exposed to air. It is also a good
idea to gently clean the tip of an optical connector with a lint-free cloth moistened
with alcohol whenever dust is suspected.
ación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que
sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
The status of the VIDEO and AUDIO indicator LEDs should provide the first clue as
to the origin of an operational failure. If these are off, it usually means that the fiber is
broken or has too much attenuation. Next, be certain that the input and output signal
connections are correct.
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser
referido a personal de servicio calificado.
If, after reviewing the above possibilities, the system is still not operating, please
contact the Black Box Tech Support for further assistance
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfi-
era su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra
o superficie similar puede bloquea la ventilación, no se debe colocar en libre-
ros o gabinetes que impidan el flujo de aire por los orificios de ventilación.
Maintenance:
The only maintenance of the AC1020A system that can be provided by the user is to
ascertain that the optical connectors are free of dust or dirt that could interfere with light
transmission and that electrical connections are secure and accurate. DANGER!Always
disconnect the transmitter power before removing the optical fiber from the unit! For
assistance with all other repairs, please contact Black Box technical support.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo am-
plificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo
2
11
AC1020A/AC1021A-XMIT/ AC1021A-REC
NOm sTaTemeNT
descrito en el instructivo de operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización
del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean
pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo
particular atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomen-
daciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas
de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea
usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derra-
mados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su
desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
Ce INFOrmaTION
Standards to which conformity is declared:
55103-2:1997
EN 55103-1:1997 EN
10
3
AC1020A/AC1021A-XMIT/ AC1021A-REC
INsTaLLaTION
Indicator LEDs:
The transmitter and receiver units in the A1020A system each have three integral in-
dicator LEDs that are used to monitor the state of the unit. Their status is as follows:
TRANSMITTER and RECEIVER:
Power: (Green) Indicates that correct power has been applied.
TRANSMITTER:
Video: OFF: Indicates no video detected on the input.
BLINKING GREEN: Indicates either H or V sync detected at the input
but not on both.
STEADY GREEN: Indicates both H and V sync detected on the input.
Audio: OFF: Indicates no audio detected on the transmitter unit.
BLINKING: Indicates audio detected on the transmitter unit.
RECEIVER:
Video: OFF: Indicates no video detected over fiber and, as a result, no
video present on output.
BLINKING GREEN: Indicates either H or V sync detected over the
fiber but not both.
STEADY GREEN: Indicates both H and V sync detected over the fiber
and, as a result, video present on the output.
Audio: OFF: Indicates no audio detected over fiber and, as a result, no active
audio detected by the receiver unit.
BLINKING: Indicates audio detected over fiber and, as a result,
active audio detected by the receiver unit.
9
4
AC1020A/AC1021A-XMIT/ AC1021A-REC
AC1020A/AC1021A-XMIT/ AC1021A-REC
INsTaLLaTION
ITems INCLUded
4. Connect the audio input signals to the transmitter stereo jack and the audio
Depending on which product you ordered, you should have received:
output to the receiver stereo jack.
AC1021A-XMIT:
Qty Description
5. Apply power to both units. Refer to Figure 1.
6. When power is applied, the green POWER
LED will light, indicating the presence of
operating power. The VIDEO LED will give
an indication as described on Page 9.
1
1
1
1
1
1
1
AC1021A-XMIT Transmitter
Power Supply
AC line cord
User Manual
7. The green AUDIO LED will give an indica-
HD15M - HD15M VGA cable, 6 ft.
3.5mm plug to 2xRCA(M) stereo audio cable, 6 ft.
3.5mm plug to 3.5mm plug stereo audio cable, 6 ft.
tion as stated on Page 9.
System Connections:
The input and output connections for the AC1020A are as follows:
AC1021A-REC :
Qty Description
Audio Connector (Transmitter and Receiver): 3.5mm stereo jack
Video Connector (Transmitter and Receiver): HD-15F connector
1
1
1
1
1
1
1
AC1021A-REC Receiver
Power Supply
AC line cord
User Manual
HD15M - HD15M VGA cable, 6 ft.
3.5mm plug to 2xRCA(M) stereo audio cable, 6 ft.
3.5mm plug to 3.5mm plug stereo audio cable, 6 ft.
Video Pin Out:
Transmitter:
Red
Receiver:
Red
1
2
Green
Green
3
Blue
Blue
4
N/C
N/C
5
6
7
8
Ground
Ground
Ground
Ground
N/C
Ground
N/C
N/C
Ground
Ground
Ground
Ground
N/C
Ground
N/C
N/C
AC1020A:
Qty Description
1
1
2
2
2
2
2
2
AC1021A-XMIT Transmitter
AC1021A-REC Receiver
Power Supplies
AC line cords
9
10
11
12
13
14
15
User Manuals
Hor. Sync In
Vert. Sync In
N/C
Hor. Sync Out
Vert. Sync Out
N/C
HD15M - HD15M VGA cables, 6 ft. each
3.5mm plug to 2xRCA(M) stereo audio cables, 6 ft. each
3.5mm plug to 3.5mm plug stereo audio cables, 6 ft. each
8
5
AC1020A/AC1021A-XMIT/ AC1021A-REC
AC1020A/AC1021A-XMIT/ AC1021A-REC
GeNeraL INFOrmaTION
GeNeraL INFOrmaTION
Optical:
Introduction:
Operating Wavelength..........................1310 nm; MM or SM
Optical Fiber ........................................50 - 62.5/125microns MM or
8-10/125 microns SM
The RGBHV Video with StereoAudio Fiber Optic Transmission System (AC1020A-
V/A System) is a transmitter/receiver pair that transmits a single channel of RGBHV
and two audio channels over one single mode or multimode fiber.
Optical Connectors...............................ST
The system’s all digital encoding delivers noise-free transmissions that retain all of
their initial parameters, regardless of fiber optic cable attenuation. System operation
may be easily monitored using integral indicator LEDs on each unit that continuously
signify the presence of baseband video and audio signals.
Wavelength
1310 MM
1310 SM
Loss Budget (in dB)
Distance* (in km)
0-0.75
0-15
0-15
0-35
*Note: Distance specifications are only approximate and are not guaranteed. Oper-
ating loss budget must not be exceeded.
Specifications:
Video:
Misc:
Operating Temperature Range .............-20 to +60 degrees C
Operating Power ..................................9 to 24 Volts AC or DC @ 5 watts (max)
Input Impedance...................................RGB: 75 ohms; H&V: Hi-Z
Input Level...........................................RGB: 714 mV p-p; H&V: 3 to 5 V p-p
H Sync Frequency Range.....................15 to 60 kHz
V Sync Frequency Range.....................30 to 85 Hz
Number of Video Channels..................1 RGBHV
RGB Format Supported .......................RGB with separate H and V
Signal Connectors................................HD-15F
CAUTION! The transmitting element in theAC1021A-XMIT transmitter is a solid-
state Laser Diode located in the optical connector on the unit. This device emits
invisible infrared electromagnetic radiation which can be harmful to human eyes.
The radiation from this optical connector, if viewed at close range without a fiber
optic cable connected to the optical connector, may be of sufficient intensity to
cause instantaneous damage to the retina of the eye. Direct viewing of this
radiation should be avoided at all times.
RGB Processing...................................24 bits, no compression or scaling
Audio:
Number of Audio Channels .................. 2, unbalanced
Frequency Response ............................. +0/-0.5 dB, 20 Hz to 20 kHz
Input Impedance.................................... >24 kOhms
Output Impedance................................. <1 Ohm
Maximum Audio Level......................... +10 dBu
THD+N ................................................. 0.005%; 20 Hz to 20 kHz
SNR (A-Weighted)................................ 95 dB
Channel Phase Differential ................... +/-0.1o
Crosstalk ............................................... Min. 95 dB (1kHz)
Signal Connectors................................. 3.5mm Stereo jack
Audio to Video Diff. Delay (skew)....... <300 uS
INsTaLLaTION
Installation Procedure:
The AC1020A fiber optic transmission system for RGBHV with Stereo Audio is de-
livered ready for immediate use. There are indicator LEDs on the units for monitoring
purposes. The following instructions describe the typical installation procedure and
the function of the LED indicators.
1. ConnectthevideosourcetothevideoinputHD-15Fconnectoronthetransmitterunit.
2. Connect the video output on the receiver unit to the HD-15F connector.
3. Connect the fiber optic cable between the transmitter and receiver unit.
7
6
|