Installation
14-063
1
S19-220HFP
P
T
.O
.
w
E
w
L
w
.b -8
ra
B
O
:
1
X
0
0
3
0
-B
9
d
le
,
R
M
E
y
c
A
o
D
rp
.c
N
O
L
E
M
O
Y
o
m
N
E
F
A
E
X
:
F
A
(2
L
L
S
-2 ,
6
2
5
W
I
1
-5
5
3
8
0
5
2
-0
3
0
1
7
)
9
U
S
A
Stainless Steel Wall-Mounted
Eyewash
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . 2
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Installation Instructions . . . . . . . . . . . . . . . . . . 4
Assembly of Components . . . . . . . . . . . . . . . . 5
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
215-158HFP Rev. J; EN 07-519
© 2007 Bradley Corporation
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX (262) 251-5817
Page 1 of 6
8/9/07
Installation
S19-220HFP
S19-220HFP Dimensions
6-15/16"
(176mm)
1/2" IPS Supply
13-1/2"
(343mm)
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
1-1/4" IPS Drain
15-3/8" (391mm)
Ø 10-3/4" (254mm)
5-9/16"
(141mm)
Ø 1"
(25mm)
7-3/8"
(187mm)
1/4"
(6mm)
2-3/8"
(60mm)
41-3/8"
(1051mm)
Suggested
Height
35-11/16"
(906mm)
Suggested
Height
4"
(102mm)
Ø 1"
(25mm)
8-1/2"
(216mm)
5/16" x 1-1/4"
(8mm x 32mm)
MOUNTING
SLOTS FOR
1/4" BOLTS
To Floor
To Floor
Ø 2" (51mm)
Figure 1
NOTE: All dimensions assume standard thread engagement. Variations in manufacturing
allow for +/- 1/8" (3mm) per threaded joint. To find the tolerance of a dimension, add
the number of thread joints in between a dimension and multiply it by 1/8" (3mm).
Bradley Corporation • 215-158HFP Rev. J; EN 07-519
8/9/07
3
S19-220HFP
Installation
Installation Instructions
Supplies Required:
• (2) 1/4" wall fasteners and bolts
• Pipe sealant
• Piping to 1/2" IPS water supply inlet and piping to 1-1/4" IPS drain outlet
• Sign-mounting hardware
Step 1: Mount eyewash and install supply piping
NOTE: The top of the eyewash heads should be 33"–45" (838mm–1143mm) from the floor. Refer to
Figure 1 on page 3 for appropriate dimensions.
1. Drill supply, drain, and operating rod holes at the dimensions shown in Figure 1.
2. Secure the eyewash receptor assembly to the wall using appropriate wall anchors and bolts (supplied
by installer).
3. Install the drain and supply piping (apply pipe sealant to all male-threaded pipe joints).
Step 2: Secure operating support sleeve
NOTE: This unit has been designed to accommodate varying wall thicknesses. When installing the
operating stem support sleeve (Item 19) it will be necessary to cut off one or both ends of the sleeve so
that 5/8" of threaded pipe protrudes from both sides of the wall.
1. Insert the operating support sleeve through the wall and secure in place with the nuts and washers
provided. A slip joint has been provided for adjustment and is located directly below the automatic
weep drain fitting (Item 11).
Step 3: Assemble components
NOTE: Refer to the illustration on page 5 for component assemblies.
1. Assemble the components in the following order over the non-threaded end of the brass tube (Item 12):
connector kit (Item 13), brass friction ring (Item 15) and rubber washer (Item 14).
2. Insert the non-threaded end into the pipe (Item 8).
3. Align and screw the threaded end into the automatic weep drain. Tighten the nut (Item 13) on the pipe.
4. Insert the operating rod (Item 22) through the sleeve and attach handles (Items 23 and 24) with
the nuts and lockwashers provided.
Step 4: Connect water supply
1. Tighten all pipes and fittings maintaining proper alignment.
2. Connect the water supply piping to the 1/2" IPS inlet on the eyewash (piping supplied by
installer).
3. Connect drain piping to the 1-1/4" IPS drain outlet on the eyewash (piping supplied by installer).
4. Mount safety sign to wall using sign mounting hardware (supplied by installer).
5. Open the water supply lines. Test for leaks and adequate water flow.
4
8/9/07
Bradley Corporation • 215-158HFP Rev. J; EN 07-519
Installation
S19-220HFP
Assembly of Components
1.10
R
P.O. Box 309, Menomonee Falls, WI 53051
TEST THIS UNIT EACH WEEK
DIESES GERÄ 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
T
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
1.9
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il
y
à
quelque chose qui ne va pas fait
un rapport immédiatement.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date
Signed
Signed
Signed
1.8
1.7
27
Flow Control
This End
1.6
1
1.5
28
16
10
P
.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
114-051
11
1.4
1.3
1.2
17
7
8
9
18
1/2" IPS
Supply Inlet
25
26
24
1.1
22.1
14
26
6
5
18.1
22
1-1/4" IPS
Drain Outlet
13
12
2
20
21
3
19
21
4
-063
114
20
13
P.
O
TEL:
w
.
B
O
ww 1-8
.bradle
0-B
0X
3
0
RAD
9,
MEN
ycorp.co
L
E
Y
O
M
F
m
NEE
AX
F
:
(26A2-L251-5817)
LS,
W
I
530
52-0
309
U
S
A
15
23
25
Figure 2
NOTE: Items 1.1-1.10 come preassembled as Item 1.
Bradley Corporation • 215-158HFP Rev. J; EN 07-519
8/9/07
5
S19-220HFP
Installation
Parts List
Item Part No.
Qty
Description
Item Part No.
Qty
Description
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
2
S90-302
111-039
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
Stainless Steel Bowl Assembly
Inlet-Drain Fitting
11
12
S29-068
142-002DA
110-191
1
1
2
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
1
1
2
2
1
1
Weep Valve Assy.
Washer
124-028
140-645
124-024
187-053
173-009
S21-071
113-1159
S05-091
107-371
169-850
113-006LT
169-849
113-006NQ
113-006NT
113-006NW
169-764
269-882
Gasket
13
Connector Nut
Wall Bracket
14
110-115
Nut
Washer
15
153-372R
169-025
Adapter, Ball Valve
90° Street Elbow 1/2" IPS
Pipe 1/2" IPS x 3-3/4" lg.
Stainless Steel Bowl
Cup Strainer
16
17
113-006MS
S27-282
Supply Pipe Assy.
18
Stay-Open Ball Valve 1/2" IPS w/Nut
Nut only
Spacer, Drain
18.1
19
110-215
Eyewash Yoke
113-006NN
113-006NR
113-006NU
142-002F
124-001F
S21-067
(0"-8")pipe sleeve 1/2" IPS x 9-1/4"
(8"-12")pipe sleeve 1/2" IPS x 13-1/4"
(12"-18")pipe sleeve 1/2" IPS x 19-1/4"
Washer-Metal
Dust Cover
45° Street Elbow 1-1/4" IPS
Pipe 1-1/4" IPS x 6-1/2" Lg.
45° Elbow 1-1/4" IPS
(0-8" wall)Pipe 1-1/4" IPS x 12-1/16"
(8-12" wall)Pipe 1-1/4" IPS x 16-1/16"
(12-18" wall)Pipe 1-1/4" IPS x 22-1/16"
Elbow 1-1/4" IPS
3
20
21
22
4
Washer-Fiber
5
(0"-8") Operating Rod
(8"-12") Operating Rod
(12"-18") Operating Rod
Retaining Ring
S21-067A
S21-067B
132-042
6
7
8
9
22.1
23
Connector
S08-308
Handle Assy.
R68-600015 4 ft.
Tube
24
128-151
Handle
113-006NP
113-006NS
113-006NV
169-838
1
1
1
1
(0"-8" wall) Pipe 1/2" IPS x 18-3/8"
(8"-12" wall) Pipe 1/2" IPS x 28-3/8"
(12"-18" wall) Pipe 1/2" IPS x 28-3/8"
Pipe Tee 1/2"
25
161-036
Nut-Hex 5/16-18 Stn. Stl.
Lockwasher
26
142-002BK
114-051
27
Safety Sign
10
28
204-421
Emergency Tag
Prepack S45-1782 includes Items 1.4, 1.6, 1.7, 1.8
6
8/9/07
Bradley Corporation • 215-158HFP Rev. J; EN 07-519
|