Lift Lever Kit
Mfg. No. 1694561
For Baron / 2400 / RD Series
Installation
Instructions
3
2
6
10
1
4
7
5
12
9
8
15
11
21
14
13
22
13
15
18
17
19
16
15
20
21
23
13 1708298
14 1732511A
15 1960074
16 1960585
17 1725957
18 1732510A
19 2157081
20 1733693
21 1919381
22 1723683
23 1724638
2
1
4
2
2
1
1
1
2
2
1
PIN, Round Head, Drilled, 3/8 x 1
BRACKET, Mounting
CLIP, Hair Pin
CAPSCREW, Hex,5/16-18 x 1-3/4
PAD, Rubber
SUPPORT PLATE
SPACER
LIFT SHAFT ASSEMBLY
WASHER, .34 x 1 x .13
PIN, CLEVIS
Kit Contents:
Ref Part No. Qty. Description
1
2
3
4
5
6
7
8
9
1725959A
1960033
1723124
1713995
1960674
1723321
1725958
1721999A
1960126
1
1
1
1
1
1
1
1
1
1
1
2
ROD & TUBE ASSEMBLY
CLIP, Hair Pin
BUTTON, Red
GRIP, Soft, Black
PUSH NUT, 1/4
SPRING, Compression
ROD, Latch
LATCH, Lift Lever
PUSH NUT, 1/4
LEVER ASSEMBLY
PIN, 3/8 x 1
GUARD ASSY, DEFLECTOR
10 1727441A
11 1927609
12 1931277
NUT, Hex, Flange Whiz Lock, 5/16-18
Figure 1. Contents
LIFT LEVER KIT FITS ON BARON / 2400 / RD
Product
Serial Number Range
Requires p/n 1726404
All
All
All
This kit adds a lift lever for front mounted
attachments.
Number
1694328
1694329
1694346
1694347
1694384
1694315
1694481
1694482
1694483
1694484
1694485
1694504
All
All
WARNING
Before beginning any service work turn off the
PTO, set the parking brake, turn off the ignition,
and disconnect the spark plug wire(s).
00001-00999
00001-00999
00001-00999
00001-00999
00001-00999
00001-00999
00001-00999
1
Lift Lever Kit
Installation Instructions
Install New Lift Shaft Assembly
BARON 2007 AND NEWER MODELS
1. Slide Lift Shaft Assy (A, Figure 7) into key-slotted
hole (existing - attached to frame (B)) aligning key in
Lift Shaft Assy (A) with key slot in hole (B).
C
2 Rotate the Lift Shaft Assy (C) 180 degree to the right
to secure the Lift Shaft Assy in place.
B
A
Figure 7. Install Lift lever Assembly
A. Lift Lever Assembly
B. Existing hole
C. Rotate Lift Lever Assembly 180 Degrees
ALL MODELS
A
Install Front Attachment Lift Lever & Rod
B
1. Slide the lift lever assembly (A, Figure 8) on to the
end of the shaft assembly and on to the edge of the
tractor.
B
D
C
2. Secure to mounting bracket (D, Figure 8) using clevis
pins (B), spacer (E), and hair pins (C).
3. Slide lift rod (A, Figure 9) into the bottom hole in the
lift lever assembly (B). Secure with hair pin (C).
Install front attachment & hitch as outlined in
Operator’s Manual or Installation Instructions.
E
End of
Shaft
Assembly
Edge of
Tractor
Figure 8. Install Lift lever Assembly
A. Lift Lever Assembly
B. Clevis Pin
C. Hair Pin
D. Mounting Bracket
E. Spacer
3
Installation Instructions
Lift Lever Kit
Install Support Assembly
1. Hang support plate (A, Figure 10) onto shaft assem-
bly (B).
B
2. The post on the support plate (A) fits between the
clamp support (C) and hitch assembly (D). See Sub-
Frame Hitch Installation Instructions for details on
installing sub frame.
C
A
Figure 9. Install Lift Rod
A. Lift Rod
C. Hair Pin
B. Lift Lever Assembly
Install Mower Deck
1. Remove Lift Lever Assembly (A, Figure 8).
B
2. Install mower deck as described in Operator’s
Manual or Dealer Setup Instructions.
A
C
Figure 10. Install Support Plate
A. Support Plate
B. Shaft Assembly
C. Clamp Support
D. Hitch Assembly
Install Deflector Guard
B
1. Install Deflector Guard Assy (A, Figure 11) using
Clevis Pins (B), Washers (C), and Hair Pins (D) as
shown.
D
C
A
Figure 11. Install Support Plate
A. Deflector Guard Assy
B. Clevis Pin
C. Washer
D. Hair Pin
Form No. 1726469-01
Rev. 11/2006
Briggs & Stratton Yard Power Products Group
Copyright © 2006 Briggs & Stratton Corporation
Milwaukee, WI USA. All Rights Reserved
TP 200-4020-01-AT-SMN
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
4
|